The relationship between machine and soil
M. Naderi-Boldaji; H. Azimi-Nejadian; M. Bahrami
Abstract
Machinery traffic is associated with the application of stress onto the soil surface and is the main reason for agricultural soil compaction. Currently, probes are used for studying the stress propagation in soil and measuring soil stress. However, because of the physical presence of a probe, the measured ...
Read More
Machinery traffic is associated with the application of stress onto the soil surface and is the main reason for agricultural soil compaction. Currently, probes are used for studying the stress propagation in soil and measuring soil stress. However, because of the physical presence of a probe, the measured stress may differ from the actual stress, i.e. the stress induced in the soil under machinery traffic in the absence of a probe. Hence, we need to model the soil-stress probe interaction to study the difference in stress caused by the probe under varying loading geometries, loading time, depth, and soil properties to find correction factors for probe-measured stress. This study aims to simulate the soil-stress probe interaction under a moving rigid wheel using finite element method (FEM) to investigate the agreement between the simulated with-probe stress and the experimental measurements and to compare the resulting ratio of with/without probe stress with previous studies. The soil was modeled as an elastic-perfectly plastic material whose properties were calibrated with the simulation of cone penetration and wheel sinkage into the soil. The results showed an average 28% overestimation of FEM-simulated probe stress as compared to the experimental stress measured under the wheel loadings of 600 and 1,200 N. The average simulated ratio of with/without probe stress was found to be 1.22 for the two tests which is significantly smaller than that of plate sinkage loading (1.9). The simulation of wheel speed on soil stress showed a minor increase in stress. The stress over-estimation ratio (i.e. the ratio of with/without probe stress) noticeably increased with depth but increased slightly with speed for depths below 0.2 m.
The relationship between machine and soil
B. Golanbari; A. Mardani; A. Hosainpour; H. Taghavifar
Abstract
Due to the numerous variables that may influence the soil-machine interaction systems, predicting the mechanical response of soil interacting with off-road traction equipment is challenging. In this study, deep neural networks (DNNs) are chosen as a potential solution for explaining the varying soil ...
Read More
Due to the numerous variables that may influence the soil-machine interaction systems, predicting the mechanical response of soil interacting with off-road traction equipment is challenging. In this study, deep neural networks (DNNs) are chosen as a potential solution for explaining the varying soil sinkage rates because of their ability to model complex, multivariate, and dynamic systems. Plate sinkage tests were carried out using a Bevameter in a fixed-type soil bin with a 24 m length, 2 m width, and 1 m depth. Experimental tests were conducted at three sinkage rates for two plate sizes, with a soil water content of 10%. The provided empirical data on the soil pressure-sinkage relationship served as the basis for an algorithm capable of discerning the soil-machine interaction. From the iterative process, it was determined that a DNN, specifically a feed-forward back-propagation DNN with three hidden layers, is the optimal choice. The optimized DNN architecture is structured as 3-8-15-10-1, as determined by the Grey Wolf Optimization algorithm. While the Bekker equation had traditionally been employed as a widely accepted method for predicting soil pressure-sinkage behavior, it typically disregarded the influence of sinkage velocity of the soil. However, the findings revealed the significant impact of sinkage velocity on the parameters governing the soil deformation response. The trained DNN successfully incorporated the sinkage velocity into its structure and provided accurate results with an MSE value of 0.0871.
N. Dibagar; A. Mardani; A. Modarres Motlagh; H. Jafari
Abstract
Introduction: Encountering soil from the viewpoint of management and product manufacturing has always been considered important, and an attempt is always made hat the tools and contrasting methods of soil be designed in such a way that itself prevents, as much as possible, the destructive consequences ...
Read More
Introduction: Encountering soil from the viewpoint of management and product manufacturing has always been considered important, and an attempt is always made hat the tools and contrasting methods of soil be designed in such a way that itself prevents, as much as possible, the destructive consequences or energy waste that include economical or environmental limitations. Enhancing the soil encountering methods, quality reformation, and its related equipment, requires performing reliable tests in actual soil conditions. Considering the complexity and variety of variables in soil and machine contrast, this is a hard task. Hence, the numeral simulations are the key of all optimizations that illustrate efficient models by removing the costly farm tests and reducing research time. Tire is one of the main factors engaged with soil, and it is one of those tools that are discussable in both farms, and software environments. Despite the complexities in soil behavior, and tire geometry, modeling, tire movement on the soil has been the researchers’ objective from the past.
Materials and methods: A non-linear finite element (FE) model of the interaction of a non-driving tire with soil surface was developed to investigate the influence of the forward speed, tire inflation pressure and vertical load on rolling resistance using ABAQUS/Explicit code. In this research numerical and experimental tests were done under different conditions in order to estimate tire rolling resistance. In numerical tests, the soil part was simulated as a one-layer viscous-elastic material with a Drucker-Prager model by considering realistic soil properties. These properties included elastic and plastic properties which were obtained in the soil laboratory using relevant tests. The soil samples were prepared from the soil which was inside the soil bin. The same soil was utilized in experimental tests. Finite strain hyper elasticity model is developed to model nearly incompressible rubber materials for the tire. Tire model consisted of three components: tread, rubber and ring. Using a soil bin and one wheel tester with their related equipment, experimental tests were carried out in the workstation of mechanics of bio system engineering department of the Urmia University. This system includes various sections such as soil storage in dimensions of 22×2×1 meter, tools carrier or tracker, soil processing equipment, dynamic system, evaluation tools and controlling systems. In order to launch the collection and supply required power for wheel carrier, an industrial three phase electromotor with 22 kW (30 hp) was used. Both numerical and experimental tests were done at three levels of wheel dynamic load (1, 2, 3, 4 and 5) kN, tire inflation pressure (100, 200 and 300) kPa and four levels of speed (0.25, 0.45, 0.65, 0.9 and 1.15) m s-1 to obtain the rolling resistance of the tire.
Results and discussion: In order to evaluate the performance of final non driving tire-soil model to estimate the rolling resistance, numerical results were compared with preliminary experimental data obtained from the soil-bin tests. The comparison showed reasonably good agreement between the computed and measured general pattern of the rolling resistance at the tire-soil interface under different speeds, vertical loads and inflation pressures. In both tests, a specified relation was not seen between tire velocity and its rolling resistance, as it was not seen in empirical models such as Wismar and Luce. Correlation coefficient between experimental and numerical data, in the minimum and maximum value of tire inflation pressure was computed to be 0.06 and 0.016 percent, respectively. The amount of tire rolling resistance significantly increased with increase of tire vertical load. Correlation coefficient between experimental and numerical data, in the minimum and maximum vertical loads was computed to be 80 and 87 percent, respectively. Gent and Walter obtained the same results. The tire inflation pressure and rolling resistance variables had inverse relation to each other in both numerical and experimental tests. Correlation coefficient between experimental and numerical data was computed to be 97 and 73 percent in the minimum and maximum tire inflation pressure, respectively. The gradient of changes in tire inflation pressure - rolling resistance diagram was less in numerical tests. This was because of differences between real properties and the properties entered into the software.
Conclusions: To conclude, in this investigation a new 3D tire-soil model was simulated which has specific features. The experimental results showed that the numerical data of estimation of non-driven tire rolling resistance were reliable. In both tests, the effect of changes in tire forward speed on rolling resistance was not significant.The amount of the tire rolling resistance significantly increased with increasing tire vertical load. Changes in tire inflation pressure and rolling resistance had an inverse relation with each other in both numerical and experimental tests. The slope of rolling resistance - inflation pressure diagram in numerical tests was less than the same diagram in the experimental tests.
H. Mohammadzadeh; A. Mardani; A. Modarres Motlagh
Abstract
The tire-mechanics models have been developed for the study of wheel movement on the road or soil surface while these models are unlikely to describe the motion of wheels on uneven surfaces. Due to dynamical complexity of this phenomena and the importance of this subject for farm conditions and the wheel ...
Read More
The tire-mechanics models have been developed for the study of wheel movement on the road or soil surface while these models are unlikely to describe the motion of wheels on uneven surfaces. Due to dynamical complexity of this phenomena and the importance of this subject for farm conditions and the wheel carrier devices, the present research aimed to investigate the effects of several parameters on the wheel passing the obstacle. The experiments were carried out using single wheel tester in soil bin condition. The results indicated a relatively linear relationship between the impact force applied on tire and forward speed of wheel and also the height of rectangular obstacle. The effect of inflation pressure was inversed in the range of complete formed tire’s body on impact force and in low levels of tire inflation pressure; tire’s body damps the maximum impact forces. The medium levels of pressure (about 150-200 kPa) resulted in less horizontal force that applied on the wheel for different levels of forward speed and obstacle’s height. Tractive force for passing obstacle was increased by raising forward speed and the obstacle’s height.