Evaluation of the Energy Efficiency of a Solar Parabolic Collector Equipped with Phase Change Materials inside the Receiver Tube of a Desalination System

Document Type : Research Article

Authors

• Zh. Seifi laleh ¹
• H. Samimi Akhijahani ¹
• P. Salami ²

¹ Department of Biosystem Engineering, Faculty of Agriculture, University of Kurdistan, Sanandaj, Iran

² Department of Biosystems Engineering, Faculty of Agriculture, University of Kurdistan, Sanandaj, Iran

https://doi.org/10.22067/jam.2023.80081.1138

Abstract

Introduction
With increasing the world's population, the demand for supply water resources is also increasing. Nevertheless, climate change has severely impacted the accessibility of fresh water resources. Consequently, researchers have been focusing on producing drinkable water from seas and oceans. Iran, with its significant levels of solar radiation and access to open water from the north and south, is an ideal country for fresh water production. Using solar water desalination systems is a reliable and cost-effective solution for producing drinking water from salt water sources. The purpose of this research is to enhance the performance of the solar water desalination system by using the latent heat storage system and a solar tracking system. In this experimental setup for fresh water production, water was used as the working fluid, while a parabolic collector functioned as the source of thermal energy.
Materials and Methods
The solar water desalination system was designed and built on a laboratory scale at the University of Kurdistan, and then the necessary experiments were carried out. The flowing fluid (water) inside the spiral tube in the tank is pumped into the absorber tube of the parabolic collector. Inside the receiver tube, there is a spiral copper tube with a 7 cm pitch, which contains paraffin. The parabolic mirror reflects the sunlight onto the receiver tube, causing the working fluid, water, to heat up. The cooling process is achieved using a specific source located in the upper section of the distillation tank. In this case, the steam droplets in the tank hit the bottom surface of this cooling tank, which has the shape of an inverted funnel, leading to condensation. The study was conducted over four consecutive days, from 10:00 to 14:00, under identical conditions from August 24th to August 27th, 2022. It took place at the Renewable Energy Laboratory, University of Kurdistan in Sanandaj, Iran, and was conducted for three different volume flow rates of fluid: 1.9, 3.1, and 4.2 l.min^-1 with phase change materials (PCM) and 4.2 l.min^-1 without phase change materials (WOPCM); the pump’s maximum flow rate was 4.2 l.min^-1. Variations of outlet temperature, thermal efficiency, desalination efficiency, and produced water were investigated under different conditions.
Results and Discussion
The results reveal that by decreasing the pitch of the spiral tube, there is an increase in the amount of heat captured, due to the increase in the Nusselt number. At the beginning of data collection, a significant amount of the energy that enters the receiver tube is absorbed by both the phase change material and the spiral tube inside the receiver and as a result, the initial air temperature is lowered. The highest temperature of salt water occurs when the fluid is flowing at a rate of 4.2 l.min^-1, while the lowest temperature is observed at a flow rate of 1.9 l.min^-1. With a flow rate of 4.2 l.min^-1, the absorbent tube rapidly transfers the absorbed heat to the salt water chamber through the fluid. The input energy to the tank has increased from 1.53 to 2.83, 1.14 to 2.18, and 0.73 to 1.48 MJ for fluid flow rates of 4.2, 3.1, and 1.9 l.min^-1, respectively. At a flow rate of 4.2 l.min^-1, the thermal efficiency of the system without phase change materials (3.51%) is lower compared to the case with phase change materials (5.02%). Moreover, using a solar tracking mechanism increased the thermal efficiency of the collector by 9.86% compared to the system using a photocell sensor. Based on the water quality values, it can be stated that the level of dissolved solids in the water sample has been significantly decreased. This indicates that the water can be used for drinking.
Conclusion
In this research, the process of thermal changes in a solar water desalination system using PCM was investigated. The obtained results demonstrate that the use of PCM improved the thermal efficiency of the collector and the water obtained from the current system is safe for consumption. Furthermore, by implementing a solar panel tracking system, the efficiency of the solar collector is improved.

Keywords

• Drinking water
• Solar collector
• Solar tracker
• Thermal efficiency
• Water quality

Main Subjects

• Agricultural systems engineering (greenhouse, fish farming, mushroom production)

©2023 The author(s). This is an open access article distributed under Creative Commons Attribution 4.0 International License (CC BY 4.0).

References

1. Abdessemed, A., Bougriou, Ch., Guerraiche, D., & Abachi, R. (2018). Effects of tray shape of a multi-stage solar still coupled to a parabolic concentrating solar collector in Algeria. Renewable Energy, 132, 1134-1140. https://doi.org/10.1016/j.renene.2018.08.074
2. Abu-Arabi, M., Al-harahsheh, M., Mousa, H., & Alzghoul, Z. (2018). Theoretical investigation of solar desalination with solar still having phase change material and connected to a solar collector. Desalination, 448, 60-68. https://doi.org/10.1016/j.desal.2018.09.020
3. Alimohammadi, Z., Samimi Akhijahani, H., & Salami, P. (2020). Thermal analysis of a solar dryer equipped with PTSC and PCM using experimental and numerical methods. Solar Energy, 201, 157-177. https://doi.org/10.1016/j.solener.2020.02.079
4. Alwan, N. T., Shcheklein, S. E., & Ali, O. M. (2021). Evaluation of distilled water quality and production costs from a modified solar still integrated with an outdoor solar water heater. Case Studies in Thermal Engineering, 27, 101216. https://doi.org/10.1016/j.csite.2021.101216
5. Bakos, G. C. (2006). Design and construction of a two-axis Sun tracking system for parabolic trough collector (PTC) efficiency improvement. Renewable Energy, 31, 2411-2421. https://doi.org/10.1016/j.renene.2005.11.008
6. Chaabane, M., Mhiri, H., & Bournot, P. (2014). Thermal performance of an integrated collector storage solar water heater (ICSSWH) with phase change materials (PCM). Energy Conversion and Management, 78, 897-903. https://doi.org/10.1016/j.enconman.2013.07.089
7. Cheng, P., & Zhan, X. (2016). Stability of organic solar cells: challenges and strategies. Chemical Society Reviews, 45, 25442582. https://doi.org/10.1039/C5CS00593
8. Duong, H. C., Cooper, P., Nelemans, B., Cath, T. Y., & Nghiem, L. D. (2015). Optimising thermal efficiency of direct contact membrane distillation by brine recycling for small-scale seawater desalination, Desalination, 374, 1-9. https://doi.org/10.1016/j.desal.2015.07.009
9. Edalati, S., Ameri, M., & Iranmanesh, M. (2015). Comparative performance investigation of mono-and poly-crystalline silicon photovoltaic modules for use in grid-connected photovoltaic systems in dry climates. Applied Energy, 160, 255-265. https://doi.org/10.1016/j.apenergy.2015.09.064
10. Elarem, R., Alqahtani, , Mellouli, S., Aich, W., Ben Khedher, N., Kolsi, L., & Jemni, A. (2021). Numerical study of an evacuated tube solar collector incorporating a nano-pcm as a latent heat storage system. Case Studies in Thermal Engineering, 24, 1000859. https://doi.org/10.1016/j.csite.2021.100859
11. Eltawil, M., Mostafa, A., Azam, M., & Alghannam, A. O. (2018). Solar PV powered mixed-mode tunnel dryer for drying potato chips. Renewable Energy, 116, 594-605. https://doi.org/10.1016/j.renene.2017.10.007
12. Esakkimuthu, S., Hassabou, A. H., Palaniappan, C., Spinnler, M., Blumenberg, J., & Velraj, R. (2013). Experimental investigation on phase change material based thermal storage system for solar air heating applications. Solar Energy, 88, 144-153. https://doi.org/10.1016/j.solener.2012.11.006
13. Goudarzi, K., Shojaeizadeh, E., & Nejati, F. (2014). An experimental investigation on the simultaneous effect of CuO–H₂O nanofluid and receiver helical pipe on the thermal efficiency of a cylindrical solar collector. Applied Thermal Engineering, 73, 1236-1243. https://doi.org/10.1016/j.applthermaleng.2014.07.067
14. Goyal, R. K., Tiwari, G. N., & Garg, H. P. (1998). Effect of thermal storage on the performance of an air collector: a periodic analysis. Energy Conversion Management, 39, 193-202. https://doi.org/10.1016/S0196-8904(96)00226-9
15. Jean, J., Brown, P. R., Jaffe, R. L., Buonassisi, T., & Bulovic, V. (2015). Pathways for solar photovoltaics. Energy and Environmental Science, 8, 1200-1219. https://doi.org/10.1039/C4EE04073B
16. Kalogirou, S. A. (2005). Use of artificial intelligence for the optimal design of solar systems. International Journal of Computer Applications in Technology, 22, 90-103. https://doi.org/10.1504/IJCAT.2005.006940
17. Khosravi, A., Malekan, M., & Assad, M. E. H. (2019). Numerical analysis of magnetic field effects on the heat transfer enhancement in ferrofluids for a parabolic trough solar collector. Renewable Energy, 134, 54-63. https://doi.org/10.1016/j.renene.2018.11.015
18. Khan, Z. U., Moronshing, M., Shestakova, M., Al-Othman, A., Sillanpaa, M., Zhan, Z., Song, B., & Lei, Y. (2023). Electro-deionization (EDI) technology for enhanced water treatment and desalination: A review. Desalination, 548, 116254. https://doi.org/10.1016/j.desal.2022.116254
19. Koca, A., Oztopb, H. F., Koyunc, T., & Varol, Y. (2008). Energy and exergy analysis of a latent heat storage system with phase change material for a solar collector. Renewable Energy, 33, 567-574. https://doi.org/10.1016/j.renene.2007.03.012
20. Kumar, B. S., Vijayan, V., & Baskar, N. (2016). Burr dimension analysis on varic material for conventionally and CNC drilled holes. Mechanical Engineering, 20, 347-354.
21. Li, P., Li, J., Pei, G., Munir, A., & Ji, J. (2016). A cascade organic Rankine cycle power generation system using hybrid solar energy and liquefied natural gas. Solar Energy, 127, 136-146. https://doi.org/10.1016/j.solener.2016.01.029
22. Lim, E. L., Yap, C. C., Teridi, M. A. M., Teh, C. H., Mohd Yusoff, A. R., & Jumali, M. H. H. (2016). A review of recent plasmonic nanoparticles incorporated P3HT: PCBM organic thin film solar cells. Organic Electronics, 36, 12-28. https://doi.org/10.1016/j.orgel.2016.05.029
23. Morad, M., El-Maghawry, H. A., & Wasfy, K. I. (2017). A developed solar-powered desalination system for enhancing fresh water productivity. Solar Energy, 146, 20-29. https://doi.org/10.1016/j.solener.2017.02.002
24. Motevali, A. (2013). Design and Evaluation of a Parabolic Sun Tracking Collector for Drying of Mint [Ph.D. Thesis.], TarbiatModares University, Tehran, Iran.
25. Mousa, H., & Abu Arabi, M. (2012). Desalination and hot water Production using solar still enhanced dy external solar collector. Desalination Water Treat, 51, 1296-1301. https://doi.org/10.1080/19443994.2012.699237
26. Muñoz, M., Rovira, A., Sánchez, C., & Montes, M. J. (2017). Off-design analysis of a hybrid Rankine-brayton cycle used as the power block of a solar thermal power plant. Energy, 134, 369-381. https://doi.org/10.1016/j.energy.2017.06.014
27. Nasri, B., Benatiallah, A., Kalloum, S., & Benatiallah, D. (2019). Improvement of glass solar still performance using locally available materials in the southern region of Algeria. Groundwater for Sustainable Development, 9, 100213. https://doi.org/10.1016/j.gsd.2019.100213
28. Panchal, H., Patel, K., Elkelawy, M., & Bastawissi, H. A. E. (2019). A use of various phase change materials on the performance of solar still: a review. International Jornal of Ambient Energy, 125, 1-6. https://doi.org/10.1080/01430750.2019.1594376
29. Pielichowska, K., & Pielichowski, K. (2014). Phase change materials for thermal energy storage. Progress in Material Science, 65, 67-123. https://doi.org/10.1016/j.pmatsci.2014.03.005
30. Rehman, H. M., Shakir, S., Razaq, A., Saqib, H., & Tahir, S. (2018). Decentralized and cost-effective solar water purification system for remote communities. in IOP Conference Series: Earth and Environmental Science. 154. https://doi.org/10.1088/1755-1315/154/1/012004
31. Rehman, S. H., & Mohandes, M. (2008). Artificial neural network estimation of global solar radiation using air temperature and relative humidity. Energy Policy, 36, 571-576. https://doi.org/10.1016/j.enpol.2007.09.033
32. Reif, J. H., & Alhalabi, W. (2015). Solar-thermal powered desalination: Its significant challenges and potential. Renewable and Sustainable Energy Reviews, 48, 152-165. https://doi.org/10.1016/j.desal.2015.07.009
33. Rostamizadeh, M., Khanlarkhani, M., & Sadrameli, S. M. (2012). Sadrameli, Simulation of energy storage system with phase change material (PCM). Energy and Buildings, 49, 419-422. https://doi.org/10.1016/j.enbuild.2012.02.037
34. Serale, G., Goia, F., & Perino, M. (2016). Numerical model and simulation of a solar thermal collector with slurry Phase Change Material (PCM) as the heat transfer fluid. Solar Energy, 134, 429-444. https://doi.org/10.1016/j.solener.2016.04.030
35. Yang, L., Zhang, X., & Xu, G. (2014). Thermal performance of a solar storage packed bed using spherical capsules filled with PCM having different melting points. Renewable Energy, 64, 26-33. https://doi.org/10.1016/j.enbuild.2013.09.045
36. Zhao, M., Liu, Z., & Zhang, Q. (2009). Feasibility analysis of constructing parabolic trough solar thermal power plant in inner Mongolia of China. In: Proc. Asia– Pacific power and energy engineering conference, 1-4. https://doi.org/10.1109/APPEEC.2009.4918378