Simulation of Heat and Mass Transfer in a Refractance Window Dryer for Aloe vera gel

Document Type : Research Article

Authors

• A. Shahraki ¹
• M. Khojastehpour ¹
• M. R. Golzarian ²
• E. Azarpazhooh ³

¹ Department of Biosystems Engineering, Faculty of Agriculture, Ferdowsi University of Mashhad, Mashhad, Iran

² Centre for Artificial Intelligence and Machine Learning, Edith Cowan University, WA 6027, Australia

³ Agricultural Engineering Research Department, Khorasan Razavi Agricultural and Natural Resources Research and Education Center, AREEO, Mashhad, Iran

https://doi.org/10.22067/jam.2023.80368.1141

Abstract

Introduction
Drying is one of the oldest methods of food preservation. To increase the efficiency of heat and mass transfer while maintaining product quality, the study of the drying process is crucial scientifically and meticulously. It is possible to conduct experimental tests, trial and error, in the drying process. However, this approach consumes time and cost, with a significant amount of energy resources. By harnessing available software and leveraging technological advancement to develop a general model for drying food under varying initial conditions, the drying process can be significantly optimized.
Materials and Methods
This study was conducted with the aim of simulating heat and mass transfer during Refractance window drying for aloe vera gel. Comsol Multiphysics version 5.6 is a three-dimensional model used to solve heat and mass transfer equations. For this purpose, the differential equations of heat and mass transfer were solved simultaneously and interdependently. The above model considered various initial conditions: water temperature of 60, 70, 80, and 90℃, and aloe vera gel thickness of 5 and 10 mm. The initial humidity and temperature of the aloe vera is uniform. The initial temperature is 4℃ and the initial humidity of the fresh aloe vera sample is 110 g_water/g_{dry matter}. Heat is supplied only by hot water from the bottom surface of the product.
Results and Discussion
The drying time was needed to reduce the moisture content of aloe vera gel from 110 to 0.1 g_water/g_{dry matter} during Refractance window drying. Aloe vera gel with a thickness of 5 mm dried in 120, 100, 70, and 50 minutes at water temperatures of 60, 70, 80, and 90℃, respectively. For a 10 mm thick layer of aloe vera gel, the drying time was 240, 190, 150, and 120 minutes, for water temperatures of 60 to 90℃, respectively. These results demonstrate the importance of both the water temperature and thickness on the drying time. Furthermore, the drying rate of aloe vera gel increased as the water temperature increased from 60 to 90℃, the drying rates were 0.915, 1.099, 1.57, and 2.198 g_water/min for 5 mm thickness and 0.457, 0.578, 0.732, and 0.915 g_water/min for 10 mm thick layer of aloe vera gel, respectively.
Conclusion
Based on the simulation results, the optimal model is with a water temperature of 90℃ and an aloe vera gel thickness of 5 mm. Overall, the modeling results are consistent with the results of experimental data.

Keywords

• Aloe vera gel
• Heat transfer
• Mass transfer
• Refractance window dryer
• Simulation

Main Subjects

• Modeling

©2023 The author(s). This is an open access article distributed under Creative Commons Attribution 4.0 International License (CC BY 4.0).

References

1. Antury, K. L. A., Rojas, D. A. V., & Bermeo, O. M. B. (2021). Conservación de las propiedades nutraceúticas del Aloe Vera (Aloe Barbadensis Miller), mediante técnicas de secado. Ingeniería y Región, (25), 6-21. https://doi.org/10.25054/22161325.2818
2. Ayala-Aponte, A. A., Cárdenas-Nieto, J. D., & Tirado, D. F. (2021). Aloe vera Gel Drying by Refractance Window®: Drying Kinetics and High-Quality Retention. Foods, 10(7), 1445. https://doi.org/10.3390/foods10071445
3. Añibarro-Ortega, M., Pinela, J., Barros, L., Ćirić, A., Silva, S. P., Coelho, E., ... & Ferreira, I. C. (2019). Compositional features and bioactive properties of Aloe vera leaf (fillet, mucilage, and rind) and flower. Antioxidants, 8(10), 444. https://doi.org/10.3390/antiox8100444
4. Beigi, M. (2019). Drying of mint leaves: Influence of the process temperature on dehydration parameters, quality attributes, and energy consumption. Journal of Agricultural Science and Technology, 21(1), 77-88.
5. Compaoré, A., Putranto, A., Dissa, A. O., Ouoba, S., Rémond, R., Rogaume, Y., ... & Koulidiati, J. (2019). Convective drying of onion: modeling of drying kinetics parameters. Journal of Food Science and Technology, 56(7), 3347-3354.
6. Dev, S. R., & Raghavan, V. G. (2012). Advancements in drying techniques for food, fiber, and fuel. Drying Technology, 30(11-12), 1147-1159. https://doi.org/10.1080/07373937.2012.692747
7. Durigon, A., Parisotto, E. I. B., Carciofi, B. A. M., & Laurindo, J. B. (2018). Heat transfer and drying kinetics of tomato pulp processed by cast-tape drying. Drying Technology, 36(2), 160-168. https://doi.org/10.1080/07373937.2017.1304411
8. Duarte‐Correa, Y., Vargas‐Carmona, M. I., Vásquez‐Restrepo, A., Ruiz Rosas, I. D., & Perez Martinez, N. (2021). Native potato (Solanum phureja) powder by Refractance Window Drying: A promising way for potato processing. Journal of Food Process Engineering, 44(10), e13819. https://doi.org/10.1111/jfpe.13819
9. Franco, S., Jaques, A., Pinto, M., Fardella, M., Valencia, P., & Núñez, H. (2019). Dehydration of salmon (Atlantic salmon), beef, and apple (Granny Smith) using Refractance window™: Effect on diffusion behavior, texture, and color changes. Innovative Food Science and Emerging Technologies, 52, 8-16. https://doi.org/10.1016/j.ifset.2018.12.001
10. Herrera Ardila, P. A. (2022) Mathematical modeling and simulation of refractance window drying of whole milk and yoghurt (Master's thesis, Universidad de La Sabana).
11. Jafari, S. M., Azizi, D., Mirzaei, H., & Dehnad, D. (2016). Comparing quality characteristics of oven dried and Refractance Window dried kiwifruits. Journal of Food Processing and Preservation, 40(3), 362-372. https://doi.org/10.1111/jfpp.12613
12. Kaur, G., Saha, S., Kumari, K., & Datta, A. K. (2017). Mango pulp drying by refractance window method. Agricultural Engineering International: CIGR Journal, 19(4).
13. Kudra, T., & Mujumdar, A. S. (2009). Advanced drying technologies. CRC press. https://doi.org/10.1201/9781420073898
14. Kumar, R., Singh, A. K., Gupta, A., Bishayee, A., & Pandey, A. K. (2019). Therapeutic potential of Aloe vera—A miracle gift of nature. Phytomedicine, 60, 152996. https://doi.org/10.1016/j.phymed.2019.152996
15. Kumar, M., Madhumita, M., Srivastava, B., & Prabhakar, P. K. (2022). Mathematical modeling and simulation of refractance window drying of mango pulp for moisture, temperature, and heat flux distribution. Journal of Food Process Engineering, 45(9), e14090. https://doi.org/10.1111/jfpe.14090
16. Khan, M. I. H., Kumar, C., Joardder, M. U. H., & Karim, M. A. (2017). Determination of appropriate effective diffusivity for different food materials. Drying Technology, 35(3), 335-346. https://doi.org/10.1080/07373937.2016.1170700
17. Mahapatra, A., & Tripathy, P. P. (2018). Modeling and simulation of moisture transfer during solar drying of carrot slices. Journal of Food Process Engineering, 41(8), e12909.
18. Milczarek, R. R., & Alleyne, F. S. (2017). Mathematical and computational modeling simulation of solar drying systems. In Solar drying technology (pp. 357-379). Springer, Singapore.
19. Nindo, C. I., & Tang, J. (2007). Refractance window dehydration technology: a novel contact drying method. Drying Technology, 25(1), 37-48. https://doi.org/10.1080/07373930601152673
20. Nindo, C. I., Feng, H., Shen, G. Q., Tang, J., & Kang, D. H. (2003). Energy utilization and microbial reduction in a new film drying system. Journal of Food Processing and Preservation, 27(2), 117-136. https://doi.org/10.1111/j.1745-4549.2003.tb00506.x
21. Ortiz-Jerez, M. J., Gulati, T., Datta, A. K., & Ochoa-Martínez, C. I. (2015). Quantitative understanding of Refractance Window™ drying. Food and Bioproducts Processing, 95, 237-253. https://doi.org/10.1016/j.fbp.2015.05.010
22. Raghavi, L. M., Moses, J. A., & Anandharamakrishnan, C. (2018). Refractance window drying of foods: A review. Journal of Food Engineering, 222, 267-275. https://doi.org/10.1016/j.jfoodeng.2017.11.032
23. Rajoriya, D., Shewale, S. R., & Hebbar, H. U. (2019). Refractance window drying of apple slices: Mass transfer phenomena and quality parameters. Food and Bioprocess Technology, 12(10), 1646-1658. https://doi.org/10.1007/s11947-019-02334-7
24. Sánchez, A. M. C., Lancheros, E. Y. M., Carvajal, M. X. Q., & Moreno, F. L. M. (2020). Sorption isotherms and drying kinetics modelling of convective and refractance window drying of feijoa slices (Acca sellowiana Berg). International Journal of Postharvest Technology and Innovation, 7(2), 118-136. https://doi.org/10.1504/IJPTI.2020.109634
25. Shende, D., Shrivastav, A., & Datta, A. K. (2019). Effect of mango puree thickness on refractance window drying for making mango leather. IMPACT: International Journal of Research in Engineering & Technology, 7, 41-54.
26. Shende, D., & Datta, A. K. (2020). Optimization study for refractance window drying process of Langra variety mango. Journal of Food Science and Technology, 57(2), 683-692. https://doi.org/10.1111/jfpp.12435
27. Shende, D., & Datta, A. K. (2019). Refractance window drying of fruits and vegetables: A review. Journal of the Science of Food and Agriculture, 99(4), 1449-1456.
28. Zou, Q., Opara, L. U., & McKibbin, R. (2006). A CFD modeling system for airflow and heat transfer in ventilated packaging for fresh foods: I. Initial analysis and development of mathematical models. Journal of Food Engineering, 77(4), 1037-1047. https://doi.org/10.1016/j.jfoodeng.2005.08.042