Fabrication and Evaluation of a Photovoltaic System with a Single-Axis Solar Tracker for Automatic Irrigation
Articles in Press, Accepted Manuscript, Available Online from 20 May 2026
https://doi.org/10.22067/jam.2026.94888.1420
H. Masoudi, H. Sayyadi, S. M. Safieddin Ardebili
Abstract Fossil fuel limitations and environmental concerns have increased interest in renewable energy sources like solar power for agricultural applications. This study presents the development and evaluation of a photovoltaic water pumping system equipped with a single-axis solar tracker, designed to automate irrigation in gardens and fields lacking access to the electrical grid. The system integrates solar energy absorption and storage, a solar tracker, and automatic irrigation units. Solar energy captured by the panel is transferred to a battery via a charge controller, then converted through a voltage converter and motor driver to operate the water pump. Experimental results indicate that the system’s energy intake peaks between 10 a.m. and 2 p.m. Under sunny conditions with an active tracker, the system stored 53.58 watts in the battery, compared to 43.4 watts with an inactive tracker, and 35.3 watts during cloudy weather. The study also found that the orientation of the solar panel relative to the sun and the use of the solar tracker significantly influenced energy collection, with statistical significance at the 5% level. Additionally, the type of soil moisture sensor impacted system performance, with a disturbance matrix demonstrating 100% irrigation accuracy. Overall, the solar tracker proved effective in sunny conditions, enhancing energy collection and system efficiency. The findings support the adoption of such systems for automatic irrigation, especially in remote or off-grid locations, contributing to sustainable agricultural practices and reducing reliance on fossil fuels. The integration of tracking technology and optimised sensor use can significantly improve the reliability and efficiency of solar-powered irrigation systems, making them a viable solution for modern agriculture.
Vacuum-infrared Drying of Okra Slices: Kinetics, Quality Analysis, and Optimisation
Articles in Press, Accepted Manuscript, Available Online from 06 January 2026
https://doi.org/10.22067/jam.2025.96137.1442
F. SalehNezhad, Y. Mansoori, S. M. Safieddin Ardebili
Abstract Okra (Abelmoschus esculentus L.) slices were dried using vacuum-infrared drying method. A laboratory-scale dryer was designed and fabricated to control the drying parameters and monitor the weight change of samples. The parameters examined included temperature (50, 55, 65, 75, and 80ºC) and absolute pressure (5, 21, 53, 85, and 101 kPa). The response factors were drying time, drying rate, effective diffusivity, specific energy consumption, colour change (ΔE and a/a0), and rehydration ratio. The results from the response surface methodology indicated that the optimal conditions for minimising drying time and maximising green colour preservation were a pressure of 5 kPa and a temperature of 51ºC. Under these conditions, the corresponding responses of dried okra slices were 173 min for drying time, 0.24 %wb min-1 for drying rate, 1.44×10-9 m2 s-1 for effective diffusivity, 32.6 kWh kg-1 for specific energy consumption, 12.64 for colour change, 0.75 for relative greenness, and 6.8 for rehydration ratio. Additionally, the findings demonstrated that the combination of pressures lower than 20 kPa with infrared drying effectively enhanced the performance factors of the dryer while preserving the colour of dried okra slices.
Investigating the Effect of Increasing Nano Cellulose to Diesel Fuel on Emission and Performance of Internal Combustion Engine
Volume 12, Issue 4, Autumn 2022, Pages 575-585
https://doi.org/10.22067/jam.2021.70608.1042
A. Waismoradi, M. E. Khorasani, H. Bahrami, S. M. Safieddin Ardebili, H. Zaki Dizaji
Abstract Introduction
Today, the number of diesel engines is increasing due to their high efficiency and low greenhouse gases. In the present study, the effect of adding nano cellulose as nanoparticles to diesel fuel on the performance parameters and emissions of diesel engine was investigated. Nano cellulose was provided by the Nano Novin Company in Sari. Nano cellulose values were considered at 3 levels of zero, 25 ppm and 75 ppm. Also, the tests were performed at 3 engine speed of 1600, 2000 and 2400 rpm in full load mode.
Materials and Methods
In this study, nanocellulose was used as nanoparticles to add to diesel and to evaluate the performance and emission parameters of the engine. To prevent the deposition of nano cellulose in diesel fuel, jelly type nano cellulose was used. The samples were named after adding different amounts of nano cellulose, abbreviated D100N0, D100N25 and D100N75. D100 means 100% pure diesel and N means different amounts of nano cellulose with different amounts. Ultrasound was used to obtain homogeneous samples. About 3 liters were prepared from each sample so that it could be used for at least 3 repetitions. The required tests were performed at three different speeds of 1600, 2000 and 2400 rpm in full load mode. The necessary equipment was used to measure the performance parameters and air emissions, including diesel engine connected to the dynamometer, emissions measuring device, fuel system and control room (to apply the load and provide conditions for each treatment and data collection). The air-cooled, four-stroke, compression-ignition single-cylinder engine made by the Italian company Lombardini was used. The D400 eddy current dynamometer made in Germany was used. The ability to measure power by this dynamometer is a maximum of 21 hp, a maximum speed of 10,000 rpm and a maximum torque of 80 N.m. To measure of emissions, the MAHA MGT5 emissions meter was used. This device is able to measure the values of CO, CO2, NOX, O2 and UHC.
Results and Discussion
The results showed that increasing engine speed in all fuel combinations increased engine power, specific fuel consumption, carbon monoxide and unburned hydrocarbons and decreased torque. Also, increasing the amount of nano cellulose per engine speed increased the amount of power and torque, but reduced the specific fuel consumption, carbon monoxide and unburned hydrocarbons. The amount of NOX increased with increasing engine speed, but at each engine speed the addition of 25 ppm nanocellulose to pure diesel significantly increased the amount of NOX. But at low speed, increasing 75 ppm nanocellulose to pure diesel reduced the amount of NOX.
Conclusion
The results of this study showed that the addition of nano cellulose as nanoparticles can improve the performance of diesel engines and also reduce the amount of emissions gases emitted from the engine. The results also showed that increasing 25ppm nanocellulose had a greater effect on engine performance. But to reduce the amount of emissions, 75 ppm nanocellulose was better.
Effect of Gaseous Fuels and Coolant Temperature on Performance and Combustion Characteristics of a Low-Speed Single Cylinder Diesel Engine
Volume 12, Issue 3, Summer 2022, Pages 351-366
https://doi.org/10.22067/jam.2021.68089.1007
B. Sabahi, H. Bahrami, M. J. Sheikhdavoodi, S. M. Safieddin Ardebili, E. Houshyar
Abstract Introduction
Today, diesel engines provide the main power source for the world equipment e.g., common propulsion generators in industry and agriculture. These engines are widely used due to their high combustion efficiency, reliability, compatibility, and cost-effectiveness. However, diesel engines are one of the most critical consumers of fuel which in turn causes some environmental pollution. One of the convenient and low-cost ways to reduce the pollution of these engines is dual-fuel mode and the use of gaseous fuels as an alternative fuel. This study investigated the effect of blending CNG and LPG with neat diesel in dual-fuel mode. Besides, the variation in engine coolant temperature on engine performance characteristics was experimentally studied.
Materials and Methods
The experimental apparatus consisted of a stationary, four-stroke, naturally aspirated, water-cooled, single-cylinder compression ignition engine. To control the engine load, an electrical dynamometer was made using a 7.5 kW three-phase generator and coupled to the engine as a cradle. A load cell was used to determine the force applied to the generator. The engine speed was monitored continuously by a tachometer. Fuel consumption was measured by using a weight method. A thermostat with variable temperature was used to control the temperature of the engine coolant. To measure the mass flow of air entering the cylinder, an airbox with a sharp edge orifice was used. For this study, factorial experiments in the form of a randomized complete block design with three replications were utilized to analyze the data statistically. The studied parameters were three levels of fuel ratio (100% diesel, 20% diesel and 80%± 2% CNG, 20% diesel and 80%±2% LPG), 11 engine speeds (1500 to 1600 rpm with 10 rpm intervals), and three engine coolant temperatures (50, 60, and 70 °C). All experiments were conducted in the governor control mode.
Results and Discussion
The results showed that the torque, brake power and brake mean effective pressure (BMEP) in the diesel-CNG mode at all engine speeds and in the diesel-LPG mode at low engine speeds significantly increased compared to pure diesel. The increases in these parameters in the diesel-CNG mode were 18.67%, 19.56% and 19.85%, and in the diesel-LPG mode were 14.02%, 13.86% and 14.2%, compared to those related to the pure diesel, respectively. This increase could be due to the high calorific value of gas fuels and improvement of combustion inside the cylinder due to the formation of homogeneous charge. At low engine speeds, the reductions in the brake specific fuel consumption (BSFC) and brake specific energy consumption (BSEC) for coolant temperature 60 °C were 11.21% and 10.77%, compared to coolant temperature 50 °C, respectively. Also, the BSFC and BSEC for diesel-CNG dual-fuel mode decreased by 8.12% and 10.81%, respectively. These values for the diesel-LPG dual-fuel mode were 5.4% and 2.4%, respectively. The brake thermal efficiency (BTE) also showed a significant increase at high speeds and when using the dual-fuel operational mode. However, raising the coolant temperature due to reducing the heat losses of the engine increased the BTE. The increases in BTE for coolant temperatures 60 and 70 °C were 7.19% and 4.37%, compared to the coolant temperature of 50 °C, respectively. When using the engine in dual-fuel mode, the volumetric efficiency due to reducing the air ratio showed a significant reduction. These diesel-CNG and diesel-LPG dual-fuel mode values were 20.31% and 24%, respectively. Furthermore, raising the coolant temperature diminished the volumetric efficiency. The reduction in volumetric efficiency for the coolant temperatures of 60 °C and 70 °C were 6.84% and 19.91% compared to the coolant temperature of 50 °C, respectively.
Conclusion
The following conclusions can be deduced based on this study:
The use of gaseous fuels as the main fuel and with a small amount of diesel in compression ignition engines is possible and improves the engine's performance characteristics.
In the diesel-CNG mode, torque, brake power and BMEP at all engine speeds and in the diesel-LPG mode at low engine speeds significantly increased compared to pure diesel because of improved combustion inside the cylinder.
At low engine speeds, increasing the coolant temperature reduced the BSFC and BSEC. Also, in the dual-fuel mode compared to the engine with baseline diesel fuel, the BSFC and BSEC were significantly lower due to the higher calorific value of gaseous fuels and higher power generation.
The BTE at high engine speeds and when the engine was in dual-fuel mode showed a significant increase. Also, increasing the coolant temperature due to reducing the heat losses of the engine increased the BTE.
When using the engine in the dual-fuel mode, due to the volume of air replaced by the gas, the volumetric efficiency showed a significant reduction. Also, raising the coolant temperature diminished the volumetric efficiency.
Overall, it can be stated that the use of a diesel-CNG dual-fuel mode with a coolant temperature of 60 °C at entire engine speeds has the best outputs on the performance and combustion characteristics of the engine.
