with the collaboration of Iranian Society of Mechanical Engineers (ISME)
Author = P. Salami
Structural and Material Engineering for Agricultural Systems

Assessing the Influence of Copper Oxide Nanoparticles Combined with Distilled Water on PVT System Performance

Volume 16, Issue 3, Summer 2026, Pages 507-523

https://doi.org/10.22067/jam.2025.92457.1349

M. Ghaderi, P. Salami, H. Samimi Akhijahani, S. Zareei, M. Safvati

Abstract The rapid growth of the global population and the increasing demand for energy, coupled with the urgent need for environmental conservation, have prompted researchers to explore renewable energy sources as viable alternatives to non-renewable fossil fuels. This study evaluates the performance enhancement of photovoltaic/thermal (PVT) systems using an immersion cooling method with copper oxide nanofluids. The experimental setup included a glass chamber immersing the panel surface, tested at nanofluid volume ratios of 0.025% and 0.05%, and flow rates of 0.01 and 0.02 L s-1. The immersion height was 5 cm within the glass chamber. The tests were conducted under ambient conditions, which included an ambient temperature of 20.6-31.2 ℃ and an irradiance of 343-924 W m-2. Results demonstrate that copper oxide nanofluids at a 0.05% volume ratio and a 0.02 L s-1 flow rate improved thermal efficiency to 31.87% and reduced panel surface temperature by up to 11.8 °C compared to water cooling. Also, the electrical efficiency of the PVT system exceeded that of the reference panel. The overall efficiency of the PVT system reached 41.89%. These findings highlight the potential of nanofluid-based cooling to optimize PVT system efficiency by enhancing thermal management.

Sustainability and Circular Bioeconomy, and Environmental Resilience

Optimization of the Canola Harvester Blade Based on Energy Reduction Approach and Life Cycle Assessment

Volume 16, Issue 3, Summer 2026, Pages 525-548

https://doi.org/10.22067/jam.2025.92546.1353

Gh. Ahmadzade, M. R. Maleki, P. Salami, K. Mollazade

Abstract Grain harvesting operations account for approximately 25-30% of total direct energy consumption in crop production systems. Developing appropriate blades for harvesting canola (Brassica napus L.) is crucial due to its distinct characteristics compared to other cereal grains. This study investigated the effects of blade angles (placement angles: 30°, 45°, and 60°; sharpness angles: 30°, 45°, and 60°), reciprocating movement speed (800, 1100, and 1400 courses per minute), and moisture levels (19%, 22%, and 24%) on reducing force, shear stress, and energy consumption during canola harvesting. Results showed that a blade sharpness angle of 30° yielded the lowest shear stress (0.175 N mm-2) compared to 60° (0.303 N mm-2). The 45° blade placement angle demonstrated minimum shear stress (0.177 N mm-2) versus 60° (0.320 N mm-2). Increasing moisture content from 19% to 24% reduced shear stress from 0.256 N mm-2 to 0.200 N mm-2. The highest reciprocating speed (1400 courses per minute) resulted in the lowest shear stress (0.167 N mm-2) compared to 800 courses per minute (0.286 N mm-2). Life cycle assessment revealed that varying blade placement angles (30° to 60°) could increase marine aquatic ecotoxicity by up to 55,762.55 kg dichlorobenzene equivalent, while changes in blade sharpness angles and reciprocating speed could lead to increases of 377,429.87 kg and 143,185.69 kg dichlorobenzene equivalent, respectively. The optimal configuration—comprising a sharpness angle of 30°, a placement angle of 45°, a moisture content of 24%, and a reciprocating speed of 1400 courses per minute—significantly reduced both shear energy and environmental impact.

Sustainability and Circular Bioeconomy, and Environmental Resilience

Evaluation of the Energy Efficiency of a Solar Parabolic Collector Equipped with Phase Change Materials inside the Receiver Tube of a Desalination System

Volume 14, Issue 2, Spring 2024, Pages 177-195

https://doi.org/10.22067/jam.2023.80081.1138

Zh. Seifi laleh, H. Samimi Akhijahani, P. Salami

Abstract Introduction
With increasing the world's population, the demand for supply water resources is also increasing. Nevertheless, climate change has severely impacted the accessibility of fresh water resources. Consequently, researchers have been focusing on producing drinkable water from seas and oceans. Iran, with its significant levels of solar radiation and access to open water from the north and south, is an ideal country for fresh water production. Using solar water desalination systems is a reliable and cost-effective solution for producing drinking water from salt water sources. The purpose of this research is to enhance the performance of the solar water desalination system by using the latent heat storage system and a solar tracking system. In this experimental setup for fresh water production, water was used as the working fluid, while a parabolic collector functioned as the source of thermal energy.
Materials and Methods
The solar water desalination system was designed and built on a laboratory scale at the University of Kurdistan, and then the necessary experiments were carried out. The flowing fluid (water) inside the spiral tube in the tank is pumped into the absorber tube of the parabolic collector. Inside the receiver tube, there is a spiral copper tube with a 7 cm pitch, which contains paraffin. The parabolic mirror reflects the sunlight onto the receiver tube, causing the working fluid, water, to heat up. The cooling process is achieved using a specific source located in the upper section of the distillation tank. In this case, the steam droplets in the tank hit the bottom surface of this cooling tank, which has the shape of an inverted funnel, leading to condensation. The study was conducted over four consecutive days, from 10:00 to 14:00, under identical conditions from August 24th to August 27th, 2022. It took place at the Renewable Energy Laboratory, University of Kurdistan in Sanandaj, Iran, and was conducted for three different volume flow rates of fluid: 1.9, 3.1, and 4.2 l.min-1 with phase change materials (PCM) and 4.2 l.min-1 without phase change materials (WOPCM); the pump’s maximum flow rate was 4.2 l.min-1. Variations of outlet temperature, thermal efficiency, desalination efficiency, and produced water were investigated under different conditions.
Results and Discussion
The results reveal that by decreasing the pitch of the spiral tube, there is an increase in the amount of heat captured, due to the increase in the Nusselt number. At the beginning of data collection, a significant amount of the energy that enters the receiver tube is absorbed by both the phase change material and the spiral tube inside the receiver and as a result, the initial air temperature is lowered. The highest temperature of salt water occurs when the fluid is flowing at a rate of 4.2 l.min-1, while the lowest temperature is observed at a flow rate of 1.9 l.min-1. With a flow rate of 4.2 l.min-1, the absorbent tube rapidly transfers the absorbed heat to the salt water chamber through the fluid. The input energy to the tank has increased from 1.53 to 2.83, 1.14 to 2.18, and 0.73 to 1.48 MJ for fluid flow rates of 4.2, 3.1, and 1.9 l.min-1, respectively. At a flow rate of 4.2 l.min-1, the thermal efficiency of the system without phase change materials (3.51%) is lower compared to the case with phase change materials (5.02%). Moreover, using a solar tracking mechanism increased the thermal efficiency of the collector by 9.86% compared to the system using a photocell sensor. Based on the water quality values, it can be stated that the level of dissolved solids in the water sample has been significantly decreased. This indicates that the water can be used for drinking.
Conclusion
In this research, the process of thermal changes in a solar water desalination system using PCM was investigated. The obtained results demonstrate that the use of PCM improved the thermal efficiency of the collector and the water obtained from the current system is safe for consumption. Furthermore, by implementing a solar panel tracking system, the efficiency of the solar collector is improved.