Co-digestion of Wastewater Treatment Plant Sludge and Plate Scrap to Increase Biogas Yield
Articles in Press, Accepted Manuscript, Available Online from 16 September 2025
https://doi.org/10.22067/jam.2025.92821.1363
W. Asrat, K. Purushottam Kolhe
Abstract This research seeks to determine the highest possible yield by integrating wastewater treatment plant sludge with food waste from plate scraps at Adama Science and Technology University (ASTU) in Ethiopia. Feedstock characterization and biogas co-generation were done on different Plate Scrap (PS), Wastewater Treatment Plant Sludge (WTPS), and 100 ml cow manure combination ratios. The feedstocks were evaluated for their TS and MC before combination, and TS, VS, TDS, COD, BOD, and pH after combination. This experiment was done in two rounds using three water baths and twenty-seven Batch Reactors (BR) with 2.5 L volume each. In the first round, eighteen reactors were used, and nine were used in the second experiment. Triplicate testing was used to evaluate the feedstock sample characteristics and to run the experiment. The reactors were operated for thirty-five days at a hydraulic retention time and a temperature of 50 °C. The daily biogas yield using the water displacement method, total biogas yield, and methane composition were measured and reported. Three sub-reactors were considered to find the average biogas yield of individual reactors. A notable increase in both daily and total biogas yield was observed with the reactor composition of 75% PS Injera (PSI) flat bread and 25% WTPS. The daily maximum and the average biogas yields were 220 mL and 810 mL, with the TS of 55,066 mg L-1 and the VS of 51,000 mg L-1. The maximum methane inside the produced biogas was 68%, from PSI75% and WTPS25%. This combination also showed the highest biogas yield.
Modification and Analysis of Integrated Enset (Ensete ventricosum) Processing Machine Components
Volume 16, Issue 3, Summer 2026, Pages 399-425
https://doi.org/10.22067/jam.2025.91751.1334
B. Adugna, K. Purushottam Kolhe, M. Gutu
Abstract This research aimed to enhance the design and functionality of an integrated enset processing machine by focusing on key components such as the shaft, cylinder drum, breastplate, and drum blade. Existing enset processing machines suffer from inefficiencies due to component wear, mechanical breakdowns, and suboptimal design, leading to operational challenges. To address these issues, targeted design modifications were planned for the machine’s components. The materials for these components were selected according to ASTM standards. The modified components were rigorously analyzed using the Finite Element Method in the Workbench module of ANSYS 2023 R1 software at Adama Science and Technology University, Adama, Ethiopia. The study reported maximum stresses of 120 MPa, 250 MPa, 400 MPa, and 260 MPa, and minimum stresses of 30 MPa, 70 MPa, 120 MPa, and 80 MPa for the shaft, cylinder drum, blade, and breastplate, respectively. Maximum deformations were found to be 0.15 mm, 0.3 mm, 0.55 mm, and 0.35 mm for these components, with a maximum safety factor of 15 for all. These results indicate that the modifications provide safe working conditions. The design ensures that the drum, drum blade, and breastplate possess sufficient rigidity to withstand operational forces, with minimal deformation (2.39×10⁻⁶ mm for the drum blade), remaining within a safety factor limit of 1.25. Additionally, the machine demonstrated excellent energy dissipation and vibrational response, indicating structural robustness.
Physical Property Characterization of Ethiopian Maize Varieties for Adaptive Multi-Crop Planter Design
Volume 16, Issue 3, Summer 2026, Pages 549-561
https://doi.org/10.22067/jam.2025.92654.1356
D. Girma Gadisa, K. Purushottam Kolhe, S. Kedir Busse, M. Mohammed Issa, T. Aseffa Abeye, D. Alemu Anawte
Abstract Smallholder maize production in sub-Saharan Africa, crucial for regional food security, grapples with persistent yield gaps driven by labor-intensive planting practices and a critical lack of mechanization specifically designed to accommodate the traits of native plant varieties. This study characterizes three maize varieties (CML-539, Melkassa 3, and Melkassa 6Q) to develop design parameters for adaptive multi-crop planters. Geometric properties including length, width, and thickness were measured using digital calipers, with 100 seeds per variety. Analysis was performed for elongation, geometric and arithmetic mean diameters, surface area, projected area, transverse cross-sectional area, sphericity, flakiness ratio, aspect ratio, shape index, and roundness. Gravimetric properties including bulk and true densities, porosity, thousand seed mass, and angle of repose were systematically analyzed to optimize seed-handling mechanisms in planter design. Physical property analysis revealed distinct varietal requirements: CML-539's irregular morphology (9.42 mm length, 49.30% porosity) necessitates vibration-assisted metering and aerated delivery systems; Melkassa 6Q's uniform properties (71.11± 6.66% sphericity, 811.62 kg m-3 bulk density) permit gravity-fed mechanisms; and Melkassa 3's intermediate characteristics of > 2.3 elongation ratio and 19.31% density variation require adjustable furrow openers of 25-30° rake angles. Geometric variability necessitates the implementation of adaptive solutions, such as curved seed tubes and adjustable furrow openers, to effectively prevent tilt and bridging. The resulting modular planter system, incorporating moisture-responsive metering, adaptive cell sizing, and aerated delivery, aligns with Ethiopia’s agroecological standards of 75 cm row spacing and depth range of 4 to 7 centimeters. This framework offers a scalable, sustainable model for precision smallholder mechanization, transferable to global maize systems.
