Design and Construction of a Disc Harrow Carrier Chassis in a Soil Bin and Measuring Its Draft Force
Volume 16, Issue 2, Spring 2026, Pages 353-363
https://doi.org/10.22067/jam.2025.92582.1372
H. Shaebani shesh poli, M. Askari, D. Kalantari
Abstract Introduction
One of the most important parts of agricultural operations is tillage, which accounts for about 60% of the total energy consumed. Therefore, reducing tillage energy demand by lowering the number of passes through the development of cost-effective machinery is highly essential in modern farming. One of the main implements that helps farmers achieve this is the disc harrow. As the most important secondary tillage tool, the disc harrow improves soil structure, breaks up clods, and increases the penetration of water and air into the soil. However, its optimal performance is influenced by parameters such as disc diameter, disc edge type (toothed or plain), disc gang angle, and tractor forward speed. Soil bins, as controlled environments for testing tillage tools, serve as an ideal alternative to agricultural lands. They allow accurate simulation of field conditions while minimizing the effects of climate change and variable soil properties.
Materials and Methods
The present study was conducted with the aim of designing, constructing, and evaluating a disc harrow carrier chassis in the controlled environment of a laboratory soil bin. First, the design phase was carried out using SolidWorks 2020 software, followed by an analysis of the design performance under maximum load using the von Mises method. The next step was the construction of the design. After construction, the evaluation phase was performed by examining the effects of four independent input variables: forward speed (6.43 and 13.15 m min⁻¹), soil moisture content (2.37 and 13.25 percent on a wet basis), disc edge type (plain or toothed), and disc gang angle (0, 15, and 30 degrees), on the dependent output variable, draft force. Each test was replicated three times, resulting in a total of 72 tests.
Results and Discussion
The results showed that the engineered chassis exhibited sufficient strength during the initial evaluation tests, with all components performing well. The findings indicated that increasing forward speed and disc gang angle led to higher draft force, while higher soil moisture levels reduced draft force. Under low moisture conditions, plain discs generated greater draft force; however, this trend reversed as moisture increased. The highest draft requirement (3.588 N) was observed for plain discs at 2.37% moisture, while the lowest (1.724 N) occurred at 13.25% moisture. At a forward speed of 6.43 m min⁻¹, plain and toothed discs required equal draft, but at 13.15 m min⁻¹, the toothed discs required substantially more draft.
Conclusion
The experiments showed that there was no significant difference in draft force between disc gang angles of 0 and 15 degrees. However, increasing the angle from 15 to 30 degrees caused a significant rise in draft force. This indicates that the initial increase in gang angle has a smaller effect, but beyond 15 degrees the impact becomes more pronounced. Therefore, selecting an appropriate disc gang angle can help reduce fuel consumption and improve the productivity of agricultural machinery. Both increasing disc gang angle and forward speed raise draft force because soil resistance to disc movement increases. At higher speeds, the disc must exert more force to cut and move the soil, leading to higher energy consumption and greater equipment wear. Conversely, at lower speeds, draft force decreases, but tillage efficiency may be reduced and plowing uniformity may be affected.
Investigating Engine Performance and Emission Characteristics during Testing of Diesel-Biodiesel Mixed Fuels Obtained from Vegetable Oils and their Modeling
Volume 15, Issue 2, Spring 2025, Pages 229-245
https://doi.org/10.22067/jam.2024.88750.1263
S. R. Mousavi Seyedi, M. Askari, S. M. R. Miri
Abstract Introduction
In Asia, two-wheeled agricultural tractors predominantly use single-cylinder two-stroke diesel engines, which are characterized by high fuel consumption and substantial air pollution. At the same time, the severe environmental impacts of energy production from diminishing fossil fuel reserves are increasingly evident. Therefore, it is essential to develop sustainable and clean energy sources to meet these needs. Biodiesel is an alternative fuel that can be blended with conventional diesel to help reduce environmental pollution. In this study, diesel-biodiesel blends produced from rapeseed, soybean, and palm oil were evaluated for their effects on engine performance metrics, including power (P), torque (T), and specific fuel consumption (SFC). Furthermore, the emissions of pollutants (NOx, HC, CO, and CO₂) from these fuels were measured and modeled using linear and non-linear regression, as well as the adaptive neuro-fuzzy inference system (ANFIS).
Materials and Methods
To leverage the benefits of palm oil biodiesel, known for its high calorific value, along with the low kinematic viscosity of biodiesel derived from soybean and rapeseed oils, pure diesel was blended with 10% and 20% mixtures of rapeseed, soybean, and palm biodiesel, as well as 10% and 20% combinations of all three biodiesels. These nine fuel blends were tested at four engine speeds (1800, 2100, 2400, and 2700 rpm) under full load conditions. The diesel-biodiesel blends were produced at Sari Agricultural Sciences and Natural Resources University (SANRU) and transported to the engine laboratory at Tarbiat Modares University in Tehran, Iran, for detailed analysis. A total of 36 treatments were evaluated using a randomized complete block design (RCBD), incorporating four engine speeds and nine fuel types. The measured outputs included engine power, torque, specific fuel consumption, and pollutant emissions such as NOx, HC, CO, and CO₂. The collected data were used as input for modeling through both linear and non-linear regression in SPSS software, as well as ANFIS in MATLAB software.
Results and Discussion
This study evaluated nine diesel-biodiesel blends derived from palm, rapeseed, and soybean oils using a diesel engine in a controlled laboratory setting. Tests were carried out at four engine speeds—1800, 2100, 2400, and 2700 rpm—under full load conditions to assess engine performance and exhaust emissions. The results showed that for all tested fuel blends, power, specific fuel consumption, and pollutant emissions increased with engine speed, while torque decreased. Based on the findings, a blend containing 20% palm biodiesel can be used as an alternative fuel in diesel engines without requiring any modifications. The modeling results indicated that non-linear regression provided better accuracy than linear regression. However, ANFIS demonstrated a much higher correlation between actual and predicted values, with R² exceeding 0.98 for both performance parameters and emissions, compared to R² values below 0.47 for linear regression and below 0.92 for non-linear regression. The ANFIS model achieved its highest and lowest R² values at 0.99 for specific fuel consumption (SFC) and 0.98 for power (P), respectively; substantially higher than those from linear regression, which yielded 0.47 for torque (T) and 0.00 for power. Non-linear regression resulted in R² values of 0.92 for SFC and 0.60 for carbon monoxide (CO), still lower than those achieved by ANFIS. Overall, the highest R² value recorded was 0.7525 for torque, and the lowest was 0.6112 for power.
Conclusion
Single-cylinder diesel engines, which have high fuel consumption and contribute to air pollution, are commonly used in two-wheel agricultural tractors across Asia. One approach to reducing the environmental impact of fossil fuels is to use biodiesel in these engines without requiring any modifications. The results of this study showed that a 20% blend of palm biodiesel can be an effective alternative fuel for diesel engines, with no need for engine modification. Furthermore, the modeling results indicated a significantly higher correlation (R² > 0.98) between actual and predicted values of performance variables and emissions using ANFIS, compared to linear regression (R² < 0.47) and non-linear regression (R² < 0.92). Therefore, ANFIS can be effectively used to accurately predict engine performance and emission parameters.
Design, Construction and Test of a Three-point Hitch Dynamometer
Volume 1, Issue 2, 2011
https://doi.org/10.22067/jam.v1i2.11353
M. Askari, M. H. Komarizade, N. Nobakht
Abstract For measuring the draft forces exerted by implements into tractor, we use the dynamometers that are divided into pull type or three-point hitch type. For measuring the forces between the tractor and the mounted implements, three-point hitch dynamometers are used. In this research, an adjustable three-point hitch dynamometer with a draft capacity of 25 kN was designed and built which is made up from two frames that one of them placed inside the other. The force sensing elements were comprised of a loadcell that was installed between the frames. All mounted tillage implements were able to be tested by this measuring device excluding mounted implements which are powered by PTO and by using this dynamometer, the variations of implements draft force in the different tillage conditions consist of the various work depths and different forward speeds would be studied. After design and construction steps, dynamometer was calibrated, tested and evaluated. Field tests were done by using of four mounted tillage implements and obtained data were compared by obtained data from ASAE D497.5 standard formula. So with these data, the design of tines, their stems, equipment frames and the selection of the optimal size of the tillage equipments in regard of the soil type of the region and the power of the available tractors will be more scientific and reasonable.
