Design and Construction
I. Ahmadi
Abstract
IntroductionMeasurement of the draft force exerted from agricultural machineries to the tractor and the calculation of the implement power requirements is important for agriculturalists in terms of machine design and tractor-machine matching . Therefore, studies about this issue have been started from ...
Read More
IntroductionMeasurement of the draft force exerted from agricultural machineries to the tractor and the calculation of the implement power requirements is important for agriculturalists in terms of machine design and tractor-machine matching . Therefore, studies about this issue have been started from the 1950’s. Zoerbet al.,(1983) claimed that the first dynamometers have been made of spring and in reality, users had difficulties reading these dynamometers gauge due to the quick variations of the gauge pointer. Therefore the second stage was the development of the hydraulic-type dynamometers in which the oil pressure inside the hydraulic cylinder-piston set installed between machine and tractor that can be readable with a bourdontube gauge was considered as its indicator. From the first years of the 1960’s development of the strain-gauge pull-type dynamometers started. In this study, design, fabrication and evaluation of a pull-type tractor dynamometer is considered that can be used to measure and store tractor forward velocity, and horizontal component of draft force exerted from wheel-type towed implements to the tractor. Therefore, drawbar power needed to pull the machine through the soil can be calculated. This dynamometer can also be utilized to measure three-point-hitch implement’s draft force and power requirements in condition that the RNAM (1983) method was used. In addition to measure the tractor velocity with a GPS receiver instead of a fifth wheel, the other particular issue about this dynamometer is that a remote controller is used to order data acquisition commands such as starting, ending, pausing and time zeroing in the process of data gathering. Materials and MethodsIn this study an S-type strain gauge load cell (model: SS300) and a GPS receiver (model: Micro GPS antenna AGM-10 + NEO-6-M-0-001 ublox AG board) were utilized to measure the draft force and forward velocity, respectively. To calibrate the load cell sensor, in an iron material selling store, the load cell was placed between an external force with a known value and roof-type load lifter by steel cables, and external loads with the value of 1-5 ton applied to the load cell in ascending and descending order. In each loading stage, the system and measuring apparatus outputs were booked. After drawing the x-y scatter chart of paired values (system output, measuring apparatus output), regression equation between these two variables were obtained that can be utilized to calibrate this part of the system. Above-mentioned method was used to calibrate the velocity measuring part of the dynamometer with a difference that real velocity was used instead of external load and velocity output was used instead of the load cell output. After performing the calibration of the system, the developed dynamometer was utilized to measure the draft force and power requirements of a three-point-hitch moldboard plow using the RNAM method. Finally, the obtained results were compared with the other researcher’s results, and the ASAE prediction of the draft force of a moldboard plow.Results and DiscussionAccording to the results of this study, the estimated equation and its coefficient of determination for the calibration of the load cell sensor were , and respectively, and the estimated equation and its coefficient of determination for the calibration of the velocity were , and respectively. Moreover, according to the results of the field tests, draft force and the power requirements of a three-bottom moldboard plow in a silty clay loam soil with the forward velocity of was measured to be , and , respectively, that were in agreement with other studies. Furthermore, the draft force results of this study, and other studies were in the range of of the which is the moldboard plow draft prediction according to the ASAE standard.ConclusionsThis study suggests that with the aid of the RNAM method, and the developed dynamometer, the draft force and power requirements of the tillage implements can be calculated. These results can further be utilized to match the implements with the tractor or to design new tillage implements.
A. Hajiahmad; A. Jafari; A. R. Keyhani; H. Goli; B. No'doust
Abstract
In this paper, a low-cost dynamometer for rolling, steered wheels is described. The dynamometer was constructed to determine whether such an instrumented mechanism was practical. Four S-beam load cells, an Opto-counter and a potentiometer were used to obtain all moments, and forces using dynamic and ...
Read More
In this paper, a low-cost dynamometer for rolling, steered wheels is described. The dynamometer was constructed to determine whether such an instrumented mechanism was practical. Four S-beam load cells, an Opto-counter and a potentiometer were used to obtain all moments, and forces using dynamic and kinematic analysis. Minimal simplifying assumptions considered for the required calculations. Overturning, aligning and rolling resistance moments besides vertical force are directly measured by the load cells. The Opto-counter detects wheel angular velocity and the potentiometer was used to measure the steering angle. The results showed that the mechanism was very well calibrated with a coefficient of determination of over 0.99 and can be used to define wheel dynamic behavior.
Design and Construction
M. Askari; M. H. Komarizade; N. Nobakht
Abstract
For measuring the draft forces exerted by implements into tractor, we use the dynamometers that are divided into pull type or three-point hitch type. For measuring the forces between the tractor and the mounted implements, three-point hitch dynamometers are used. In this research, an adjustable three-point ...
Read More
For measuring the draft forces exerted by implements into tractor, we use the dynamometers that are divided into pull type or three-point hitch type. For measuring the forces between the tractor and the mounted implements, three-point hitch dynamometers are used. In this research, an adjustable three-point hitch dynamometer with a draft capacity of 25 kN was designed and built which is made up from two frames that one of them placed inside the other. The force sensing elements were comprised of a loadcell that was installed between the frames. All mounted tillage implements were able to be tested by this measuring device excluding mounted implements which are powered by PTO and by using this dynamometer, the variations of implements draft force in the different tillage conditions consist of the various work depths and different forward speeds would be studied. After design and construction steps, dynamometer was calibrated, tested and evaluated. Field tests were done by using of four mounted tillage implements and obtained data were compared by obtained data from ASAE D497.5 standard formula. So with these data, the design of tines, their stems, equipment frames and the selection of the optimal size of the tillage equipments in regard of the soil type of the region and the power of the available tractors will be more scientific and reasonable.