Modeling
M. Mehrijani; J. Khodaei; S. Zareei
Abstract
Introduction Tillage as a preliminary step for agricultural production consumes large amounts of energy. Regarding the energy crisis and the greenhouse gas emissions caused by the indiscriminate use of fossil fuels, many efforts have been done to reduce energy consumption as much as possible. About half ...
Read More
Introduction Tillage as a preliminary step for agricultural production consumes large amounts of energy. Regarding the energy crisis and the greenhouse gas emissions caused by the indiscriminate use of fossil fuels, many efforts have been done to reduce energy consumption as much as possible. About half of the energy used in the crop production has been dedicated to tillage operations; hence the optimization of tillage tools performance can lead to decrease the energy loss. Tillage operation in most regions of Iran is carried out by moldboard plow. The ability of this plow in turning the soil has made it impressively different from the other plows. The energy used in tillage operations depends on various factors such as soil type and its conditions (soil moisture and texture), plow depth and forward speed. The aim of this study is to investigate the effect of forward speed, plow depth and soil moisture on fuel consumption and required tensile force during tillage operation with a moldboard plow which uses three plows in clay soil. Materials and Methods The current study was carried out to optimize the tillage operation with a moldboard plow in the clay soil. Tillage experiments were performed to evaluate the effect of forward speed, plow depth and soil moisture content on the required tensile force and tractor fuel consumption. A moldboard plow with three single-sided plows was used to conduct experiments. Two tractors (MF285 and U650) and a dynamometer were used to measure the required tensile force. To measure the fuel consumption of the tractor during operation, the fuel level was measured in a separate tank system installed on the tractor's fuel system. Experiments were carried out using response surface method and central composite design (CCD) by taking three levels of forward speed (4, 5 and 6 kmh-1), three plow depth (20, 25 and 30 cm) and three levels of soil moisture content (12, 16 and 20%). Design Expert 8.0.6 software was used to analyze the experimental data. Results and Discussion The result of the analysis of variance showed that the effects of plow depth, forward speed and soil moisture, as well as the interaction between forward speed and moisture content on the fuel consumption during tillage operations with moldboard plow are significant. The results also indicated that the increase in forward speed decreased the fuel consumption. Also, fuel consumption decreased with increasing in moisture content at first, but then increased. The reason for this was probably because of the increased strength of soil particles due to the reduced moisture content (the stronger coherence force between the particles), which required more energy to shear the soil. According to the results of analysis of variance, it can be concluded that all three factors of forward speed, plow depth and soil moisture had a significant effect on the required tensile force of moldboard plow at %1 probability level. With increasing the plow depth and forward speed, required tensile force increased significantly. The dependent variables were modeled as second order regression equations and optimal values of independent variables were determined. Optimum performance with maximum desirability was determined at forward speed of 5.08 kmh-1, plow depth of 20 cm and soil moisture content of 16.41%. Conclusion With increasing plow depth, tensile force and fuel consumption increased. Also, tensile force increased with increasing forward speed, but this increase was not severely affected by the plow depth and reduced the fuel consumption. The quadratic regression models can well predict the required tensile force and fuel consumption. Using response surface method, optimum performance was determined at forward speed of 5.08 kmh-1, plow depth of 20 cm and soil moisture content of 16.41%.
M. Baghani; M. H. Aghkhani
Abstract
IntroductionIran as one of the largest producers of poultry in Asia and plays major role in feeding the world's population, particularly in the poultry industry. Research about this industry will help to improve the quality and the quantity of products. Increasing of the concentration of toxic gases ...
Read More
IntroductionIran as one of the largest producers of poultry in Asia and plays major role in feeding the world's population, particularly in the poultry industry. Research about this industry will help to improve the quality and the quantity of products. Increasing of the concentration of toxic gases such as NH3 (ammonia), CO2 (carbon dioxide), SH2 and CH4 in poultry houses comes from bird activity inside the barn is one of the basic problems of the farming. Increasing the amount of these gases more than standard level would cause heavy mortality and reductions in the production. Ammonia is one of the most toxic gases in poultry houses, which must be controlled. Different studies have been carried out on measurement of ammonia emissions from poultry houses to reduce energy consumption and reduce emissions of ammonia. But no specific study has been found on ammonia emissions in Iran and there is no reliable documents of ammonia emissions from poultry in this country.Materials and MethodsIn this study a poultry house with 18 thousand chickens was used to measure the emission rate of ammonia, the effect of temperature, moisture and age of chickens on emissions of ammonia in Sabzevar city. The barn was equipped with semi-automatic mechanical ventilation. At the first step of this research all sensors was installed for data collection, i.e., air velocity, temperature, humidity and ammonia concentration. Recorded data information were stored in a central computer. Five digital sensors, model AM2303, have been used to measure the temperature and humidity of the ambient air quality. The concentration of ammonia in the air inputs and outputs of the farm was measured using an ammonia sensor model TGS2444 every 10 seconds throughout the study and recorded in the central system. The average speed of the exhaust air was measured using the hot wire anemometer probe for every fan. The outputs of all sensors was converted to digital data and transferred to the central computer using RS485 cable in each module. Converting of the sensors output to digital data reduces changing the data and probable errors. Ammonia emission rates was found by calculating the concentration of ammonia and measuring the rate of input air and fans exhaust air by ammonia gas equilibrium equation. Relation of the ammonia emission rate was achieved using affective factors such as age of the birds and inside air humidity and temperature by regression method.Results and DiscussionThe average rate of ammonia emission during broiler growing were measured 89 mg per day for each bird. Ammonia emission rates increased until the age of 37 days and then decreased after the age of 37 days. Age of birds has the highest impact coefficient and temperature and relative humidity of the barn have the least impact coefficients on the ammonia emission rate. The ammonia emission rate has also increased by increasing the age of the bird, temperature and relative humidity of the air. Comparing of the ammonia emission rate derived from regression equation with real conditions showed that the regression equation method has a high precision for estimating the ammonia emission rate.ConclusionIt is showed that the results of this research can predict the ammonia emission rate in the poultry houses and predict the required ventilation rates to minimize the amount of ammonia concentration. The results of this study can be used for automatic control system to minimize energy consumption in the poultry houses. According to the results, the reduction of temperature and humidity in poultry house can be used to reduce the ammonia level.
K. Abbasi; M. Almassi; A. M. Borghaee; S. Minaei
Abstract
Agricultural mechanization is a method for transiting from traditional agriculture towards industrial and sustainable one. Due to the limitation of natural resources and increasing population we need to have economical production of agricultural crops. For reaching this destination; agricultural mechanization ...
Read More
Agricultural mechanization is a method for transiting from traditional agriculture towards industrial and sustainable one. Due to the limitation of natural resources and increasing population we need to have economical production of agricultural crops. For reaching this destination; agricultural mechanization has a remarkable role. So it is necessary to have an extensive view for mechanization, because with the help of mechanization the agricultural inputs such as seeds, fertilizer and even water and soil can effectively be managed for an economical and sustainable production. This study has been carried out in many provinces of Iran. The data of agricultural tractors and cereal combine harvesters were firstly gathered by means of questionnaire. The tractors were categorized in four power levels of less than 45, 45 to 80, 80 to 110, and more than 110 hp. In addition, it was also carried out for cereal combine harvesters; it was in three power levels, i.e. between 100 to 110, 110 to 155 and 155 to 210 horse-power in 3 ages, i.e. less than 13, between 13 to 20, and more than 20 years. Information regarding to cultivation areas, production volume, and yield of main crops gathered from statistics of Ministry of Jihad-e-Agriculture. Then agriculture mechanization level index (hp ha-1) in each province was calculated. Four main crops including irrigated and rain-fed wheat and irrigated and rain-fed barley, which met the required criteria to be used in the model, were statistically analyzed. Correlation analysis was carried out in order to get an effective model between yield of the four main crops in Iran and agriculture mechanization level index. Pearson correlation index showed that there is a direct and significant correlation between these variables. Subsequently, outliers were identified in order to get a model with necessary efficiency to predict the yield through mechanization level index, by scatter diagram and estimating regression lines in 1% probability level. The effective model was estimated with acceptable coefficient of determination 0.851, after removing outliers.
M. Naghipour Zade Mahani; K. Jafari Naeimi; M. Shamsi; Gh. Mohamadi Nejad
Abstract
Due to the importance of weed control and the limitations of mechanical methods in some places, in this research the water jet cutting for weed control was investigated. The cutting tests were performed on camel thorn weed in Shahid Bahonar university of Kerman. The water jet pressure of 90 bars was ...
Read More
Due to the importance of weed control and the limitations of mechanical methods in some places, in this research the water jet cutting for weed control was investigated. The cutting tests were performed on camel thorn weed in Shahid Bahonar university of Kerman. The water jet pressure of 90 bars was achieved with the aid of a suitable pump. The cutting time was studied in a completely randomized factorial design experiment (CRD) with five replications. Factors of experiments are: stem diameter in 2 levels (smaller and larger than 5 mm), distance of spraying jet from weeds in 3 levels (10, 20 and 30 cm) and two types of plant holders: blade and plate. The results showed that stem diameter and jet distance from the weed stem had significant effects on cutting time (at the 1%). The mean comparison of parameters showed that with increase of stem diameter the cutting time increased and any increase in jet distance from the weeds decreased the cutting time linearly with R2=0.96 and R2=0.99 for small and large diameter weeds, respectively. The minimum cutting time was measured at 30 cm of the jet from small diameter of stems. A multivariate linear regression model was also proposed for cutting weed parameters. It can be concluded that due to the flexibility of water jet cutting for restricted places, hydrodynamic control of weeds is proposed as a complementary method and sometimes a competing substitute method.
