with the collaboration of Iranian Society of Mechanical Engineers (ISME)
Keywords = Sugarcane planter
Agricultural and off-Road Machinery

Design, Construction, and Evaluation of an Automatic Feeder Control System for Sugarcane Billet Planters

Volume 14, Issue 4, Autumn 2024, Pages 459-474

https://doi.org/10.22067/jam.2024.88301.1254

B. Abbasian, M. E. Khorasani Ferdavani, H. Zaki Dizaji

Abstract Introduction
This study investigated the development and evaluation of an automatic feeder control system for sugarcane planters. The primary objective was to address limitations in existing machines and enhance their performance by introducing precise control of cane feeding.
Materials and Methods
The automatic feeder control system was equipped with three types of sensors, including a Load Cell Sensor that directly measures the weight of sugarcane on the feeder table. This feature provides a real-time assessment of cane availability. The Hydraulic Oil Pressure Sensor monitored the pressure within the hydraulic system that drives the feeder mechanism. Variations in pressure served as an indirect measure of the force applied to the cane during the feeding process. The Ultrasonic Distance Sensor employed ultrasonic waves to estimate the distance between the sensor and the sugarcane pile. Nevertheless, some limitations concerning accuracy and response time were identified. A microcontroller served as the central processing unit, receiving sensor data and generating control signals to regulate the feeder mechanism. This allowed for automation and eliminated the need for a manual operator. The performance of the automatic feeder control system was evaluated against a manual control method operated by a human.
Results and Discussion
The evaluation focused on three key aspects: cane spillage, planting quality, and control stability. Cane Spillage: the amount of sugarcane inadvertently dropped during the planting process. Automatic control methods using a load cell and hydraulic oil pressure sensor reduced spillage similarly to manual control, averaging approximately 8.8 t ha-1. The ultrasonic sensor resulted in significantly lower spillage, achieving 7.4 t ha-1. However, its limited accuracy and responsiveness led to undesirable gaps between the planted canes. Planting Quality: The implementation of automatic control techniques utilizing load cells and hydraulic oil pressure sensors successfully ensured uniform spacing between planted canes, achieving results comparable to traditional manual methods. Due to its shortcomings, the ultrasonic sensor created gaps between the planted canes, undermining the overall quality of the planting process. Control Stability: The method utilizing hydraulic oil pressure sensors exhibited limitations in maintaining consistent control under varying operational conditions. This stemmed from temperature-dependent changes in oil viscosity, which affected the pressure readings and ultimately the control signal. Based on the evaluation results, the load cell control method emerged as the most favorable option for automatic feeder control. It delivered performance that matches manual control in terms of cane spillage reduction and planting quality, all while eliminating the need for an operator. The hydraulic oil pressure sensor method, although effective in some aspects, presented challenges due to oil viscosity variations. The ultrasonic sensor showed promise for reducing spillage; however, it ultimately fell short due to its inability to accurately and swiftly detect the availability of cane, resulting in gaps between planted canes. A separate assessment was carried out to compare manual cultivation with an automatic control method based on weight measurements using a load cell. This evaluation revealed significant differences (p < 0.01) in billet weight, the number of billets utilized, and one-sided gaps between the two methods. However, no significant difference was observed in terms of two-sided gaps.
Conclusion
This study successfully designed and implemented an automatic feeder control system for sugarcane planters. The load cell control method emerged as the most effective solution, successfully eliminating the need for operators while ensuring high standards of planting quality and efficiency. Additional research could explore advancements in sensor technology and control algorithms to further enhance the performance of automatic feeder control systems.
Acknowledgment
The authors would like to express their gratitude to the Managing Director of Farabi Agro-Industrial Company and its staff, as well as the technical staff of Poya Sazan Sabz Avane Company, who cooperated in the preparation and evaluation stages of the system. Vice Chancellor for Research and Technology of Shahid Chamran University of Ahvaz, Iran: financial support under the special research grant number SCU.AA98.505.

Agricultural and off-Road Machinery

Design and fabrication of an exprerimental model of a seeding unit with widthwise sugarcane scions seeding for use in sugarcane planter

Volume 7, Issue 1, 2017, Pages 312-321

https://doi.org/10.22067/jam.v7i1.45290

A. Akbarnia

Abstract Introduction
Sugarcane, a plant which sugar is extracted from, is planted in vast areas with hot and humid climate. Brazil is the largest producer of sugarcane in the world. The next five major producers, in decreasing order, are India, China, Thailand, Pakistan and Mexico. Sugarcane is a tropical, perennial grass that forms lateral shoots at the base to produce multiple stems, typically three to four meters high and about 5 cm in diameter. The total area under sugarcane plantation in Iran (Khozestan Province) is about 80,000 hectares with an average yield of 100 tons per hectare. To increase the yield per unit of land and reduce production costs and move toward sustainable agriculture, mechanization of agricultural operations seems inevitable. Planters are the most important of farm machinery among the mechanization equipment. Sugarcane cultivation is done both by hand and machine. Hand planting operations is laborious and painstaking work and work efficiency is so low and culture costs are so high. In Iran farms, the sugarcane plantation process is carried out manually by the farmers. Considering the climatic conditions, the agricultural soil composition and constitution, and the different plantation pattern used in Iran, the imported planting machines are not suitable for the farming conditions in the country. Moreover, the domestically produced machines, which are mostly based on the imported versions, do not provide adequate performance. Therefore, fabrication of a machine, capable of continuously lifting the sugarcane scions from a container and sending them to a dropper pipe, uniformly and in conformance with the climatic conditions of the sugarcane farms in the country, is of great importance.
Materials and Methods
In this research, initially, a field study was carried out to identify the problems and shortcomings of imported and copied planting machines in sugarcane farms, such as jamming of the scions conveying mechanism and the existence of unplanted sections in the farm. Subsequently, a new compound seeding unit with unique capabilities for solving the above mentioned problems was fabricated, with the aim of application in sugarcane planting machines. The various components of the system include:
1- Tank split in two pieces and connected to each other by two hinges through the middle and it can adjust to different angles. 2- Tube fall for cuttings scions. 3- Two rows of chain on a conveyor screwed on belt. 4- Number of 9 cups (channels) to receive and transmit cutting scions from the tank and guided them to the falls duct. 5- 18 pcs of metal preservative, the chain screwed to conveyor. 6- Four Number of gears on two shafts in order to drive the conveyor chain. 7- Two shafts, one on top and one another on the bottom of the anchor-conveyors chain. 8- The mechanism of driven Endless belt as a mobile bed to showing the steady rate of falling the scions from the fallen channel. 9- Two variable speeds electromotor to provide the movement of complex distributer and planter’s mobile bed belt. 10- Controlling mechanism of falling number of scion.
After preparing and manufacturing the different machine’s pieces, they were installed on the chassis and then different units were prepared and the machine are run.
Results and Discussion
Therefore, fabrication of a mechanism, capable of continuously lifting the sugarcane scions from a container and sending them to a dropper pipe, uniformly and in conformance with the conditions of the sugarcane farms is of great importance. In the new mechanism, as opposed to the existing seeding units in which the seeding operation is performed lengthwise, planting of the scions is performed in a widthwise pattern. Using the manufactured machine had a great effect on method of tillage and planting. The farm field was changed to a smooth surface in tillage then in planting the scions with installing the two diagonal plate the soil putted on scions and the made furrows for irrigating.
Conclusion
This mechanism reduces the number of planted scions per hectare, results in a more uniform planting and growth of the scions, and reduces the number of machine trips in the farm, increasing the planter productivity. The seeding unit was fabricated and is presently ready for use in the sugarcane planters.