with the collaboration of Iranian Society of Mechanical Engineers (ISME)
Subjects = Biological and Biosystems Engineering
Biological and Biosystems Engineering

Quantum Health Accelerator®: A Novel Choice for Enhanced Growth of Microalgae; Arthrospira platensis and Chlorella vulgaris

Articles in Press, Accepted Manuscript, Available Online from 03 October 2026

https://doi.org/10.22067/jam.2026.97720.1476

A. A. Mohaddes, M. A. Saatchi, M. Afshari-Chamanabadi, S. Saatchi, E. Masoudi, A. Mansouri Daneshvar, S. Malekzadeh-Shafaroudi

Abstract Microalgae are a salient source of oxygen and food for the living world. Every factor that could improve the growth rate and production of these valuable organisms could be a potential approach to achieving sustainability for humans. Microalgae such as Chlorella and Arthrospira (Spirulina) act as efficient organisms in collecting sunlight energy and converting it into biomass and biochemical compounds. In this investigation, we aimed to evaluate the effects of water (Quantum Health Accelerator®-QHA) enriched with vital bio-quantum information/energy, referred to here as Energetic Water (EW), on biomass production, biochemical composition/content, and morphological characteristics of these two agriculturally significant microalgae. The tested accelerator (EW) was applied in BG11 and Zarrouk culture media for the abovementioned microalgae in different versions, made respectively by treated distilled water (EW), non-treated distilled water (Control), filtered energetic water (FEW), and autoclaved energetic water (AEW). Biomass production, biochemical composition/content, and also morphological characteristics of these two microalgae were regularly recorded. The results surprisingly revealed a significant morphological change, together with significant changes (mostly two or three times more than the control) in biomass, pigments, proteins, and cell volume, and simultaneously a higher specific growth rate (P < 0.05) after applying the quantum accelerator, and demonstrated that the real effect of this treatment is working and could be economically exploited in algae cultivation.

Biological and Biosystems Engineering

A Review on the Physicomechanical Properties of Polysaccharide-Based Edible Films Incorporating Essential Oil-Loaded Pickering Emulsions

Volume 16, Issue 3, Summer 2026, Pages 599-624

https://doi.org/10.22067/jam.2025.92162.1343

H. Mirzaee Moghaddam, A. Nahalkar, A. Rajaei

Abstract Pickering emulsion-based edible biodegradable films have emerged as a promising sustainable alternative to conventional food packaging materials. These films exhibit enhanced mechanical properties, including tensile strength, flexibility, and water vapor barrier performance, which are critical for maintaining food integrity throughout storage and transportation. A key advancement in this field is the incorporation of essential oils into the emulsion matrix, which, despite their hydrophobic nature, significantly improve the functional and mechanical properties of polysaccharide-based films. This review examines the physicomechanical properties of polysaccharide-based edible biodegradable films incorporating Pickering emulsions, with a focus on flexibility, tensile strength, water vapor permeability, and moisture retention capacity. Furthermore, it explores the role of these films in extending food shelf life and analyzes how interactions between essential oils and polysaccharides influence their structural and barrier properties. Findings demonstrate that Pickering emulsions containing essential oils substantially enhance the mechanical and moisture barrier performance of edible biodegradable films. Solid stabilizing particles contribute to increased tensile strength, while essential oils improve flexibility—though excessive concentrations may compromise structural integrity. Additionally, these emulsions reduce water absorption and solubility, thereby improving film stability in humid conditions. Finally, this review examines the current challenges and identifies key research opportunities in the development of essential oil-loaded Pickering emulsion systems for polysaccharide-based biodegradable films, while outlining their potential for scalable industrial applications.

Biological and Biosystems Engineering

Investigation of the Structural and Physicomechanical Properties of Edible Sodium Carboxymethyl Cellulose Based Bilayer and Composite Films Containing Walnut Oil Emulsion Stabilized with Chia Seed Gum

Volume 16, Issue 1, Winter 2026, Pages 137-152

https://doi.org/10.22067/jam.2025.90690.1312

A. Nahalkar, A. Rajaei, H. Mirzaee Moghaddam

Abstract This study investigated the effects of walnut oil incorporation on the physicomechanical and structural properties of sodium carboxymethyl cellulose-based edible films, with a focus on two methods of oil addition: bilayer and composite configurations. For this purpose, firstly walnut oil Pickering emulsion (10% oil) was stabilized using chia seed gum, which was then incorporated into the formulation of bilayer and composite films. SEM revealed that bilayer film exhibited a more cohesive and homogeneous structure compared to the composite film. XRD analysis indicated a semi-crystalline amorphous structure across all films, with bilayer film displaying slightly sharper peaks than composite film. Moisture content and solubility tests highlighted the hydrophobic influence of walnut oil, with bilayer films exhibiting the lowest moisture content and solubility due to their surface-localized oil layer. Thermal analysis using DSC and TGA demonstrated improved thermal stability and reduced weight loss in bilayer film. Mechanical tests showed that the bilayer film had the highest elongation at break (34.3%) and the lowest tensile strength (3.4 MPa). Color analysis revealed significant changes in chromatic indices, with composite films showing higher saturation and total color difference. These findings underscore the potential of walnut oil emulsion stabilized with chia seed gum, particularly in bilayer configurations, to enhance the functional properties of sodium carboxymethyl cellulose-based films.

Biological and Biosystems Engineering

Evaluation of Mechanical Properties of Polylactic Acid (PLA) Films Over One and Ten Months of Aging

Volume 16, Issue 1, Winter 2026, Pages 153-166

https://doi.org/10.22067/jam.2025.90838.1316

N. Tajari, H. Sadrnia, F. Hosseini

Abstract Polylactic acid (PLA) is a thermoplastic, biodegradable, and bioactive polymer obtained from renewable resources such as beets and potatoes. PLA is regarded as a polymer that is nearly brittle, which can restrict its applications in the packaging industry. The mechanical properties of this polymer can be improved by adding nanoparticles and plasticizers. In this research, zinc oxide nanoparticles (1 wt% of PLA), Polyethylene glycol 400 (20 wt% of PLA), and Polysorbate 80 (0.25 wt% of the solution) were used to improve the mechanical properties of PLA films. The effects of these materials on the films were measured at two time points: the first month and the tenth month, with the aim of investigating physical aging, a precursor to polymer degradation. Statistical analysis was performed on the mechanical properties measured during these periods to identify significant differences between the produced films. Results showed that the highest tensile strength (82.99± 1.90 MPa, neat PLA), elongation at break (76.82± 27.22 %, PLA/PEG/ZnO), toughness (20.13± 7.89 J cm-3, PLA/PEG/ZnO), and Young's modulus (2.74± 0.10 GPa, neat PLA) were observed in the first month. Analysis of variance results regarding the effect of time on each film revealed that in most cases, the mechanical properties did not change significantly after ten months. Based on the stress-strain curves, it was found that the neat PLA film is among the resistant materials. The PLA/Polysorbate/ZnO film exhibited brittle behavior in the tenth month. The remaining samples exhibited characteristics that fell between resistant and ductile materials in both the first and tenth months.

Biological and Biosystems Engineering

Effect of Magnetic Field on Seeds of Parsley (Petroselinum crispum): Modeling and Optimization by Response Surface Methodology

Volume 15, Issue 3, Summer 2025, Pages 305-318

https://doi.org/10.22067/jam.2024.88417.1256

M. Rafiei, F. Khoshnam, M. Namjoo

Abstract In the current study, the modeling and optimization of various seedling growth and germination indices for parsley seeds were investigated. A lab-scale quadrupole magnetic field was developed, and experiments were conducted using a completely randomized factorial design with three replications. The factors considered were magnetic field intensity (150, 300, and 450 mT), exposure time (30, 60, and 90 minutes), and culture time (0, 7, and 14 days after applying the magnetic field). The results revealed that the magnetic field significantly affected shoot length, fresh root weight, and fresh shoot weight, while exposure time significantly impacted root length. Sowing day also significantly influenced root length and fresh root weight, along with other factors. Immediate sowings after magnetic field application enhanced root length, while sowing 14 days following the exposure increased shoot length, fresh root weight, and fresh shoot weight. A 30-minute exposure to magnetic field intensities of 150 to 300 mT did not significantly affect seedling growth parameters. However, higher field strengths of 450 mT for 60 to 90 minutes proved beneficial, leading to enhanced shoot length, fresh root weight, fresh shoot weight, germination rate, germination percentage, and reduced mean germination time. The analysis and optimization using Response Surface Methodology revealed that the optimal magnetization condition, with a desirability of 0.682, was achieved at a magnetic field of 450 mT, an exposure time of 60 minutes, and sown 14 days post-exposure. Higher magnetic fields appeared to enhance field durability and significantly impact seedling growth indices.

Biological and Biosystems Engineering

Construction and Performance Evaluation of a Flow Meter Based on Thermal Pulse to Measure Plant Sap Flow in Vascular Tissues

Volume 15, Issue 2, Spring 2025, Pages 165-177

https://doi.org/10.22067/jam.2023.81221.1150

M. Teimorzadeh, J. Baradaran Motie, A. Rohani, Y. Selahvarzi

Abstract Introduction
Neglecting the water requirements of trees can result in inefficient irrigation practices, leading to either water wastage or drought stress. Effective irrigation management necessitates precise information on the quantity and pattern of water consumption by trees. To achieve optimal irrigation, a reliable method for quantifying plant water needs is crucial, ensuring that trees avoid drought stress. Current methods for assessing tree water requirements often focus on specific components, such as stems or leaves. These techniques typically require manual intervention, which is time-consuming and resource-intensive, thereby restricting their application mainly to research environments.
Materials and Methods
A sap-flow meter device was developed to generate a heat pulse in a tree trunk at 15-minute intervals. The device comprises measuring probes, a processing unit, and a data logger. For a comprehensive evaluation, device probes were positioned on the trunk of a Ficus benjamina tree within a controlled environment at two distinct heights. The resulting sap flow through the vascular tissue was then compared to data obtained using the lysimetric method. The Ficus benjamina tree, with a trunk diameter of 3.5 cm and a height of 196 cm, was prepared during the summer of 2022. By measuring the rate of heat pulse dissipation and applying heat transfer principles, sap flow is estimated under the assumption that heat transfer occurs primarily through the sap flow within the vascular tissue. This estimation was achieved using the heat ratio method (HRM).
The trunk was triple drilled with holes of 1.5 mm in diameter and 25 mm in depth. Following drilling, the probes were inserted into these holes (Figure 1). To prevent heat transfer from the probes to the surrounding environment, the trunk was wrapped with glass wool insulation. To assess the reliability of the device, the lysimetric method was employed to measure tree transpiration. For this purpose, the soil surface of the pot was covered with cellophane to ensure that evaporation and weight loss of the pot occurred exclusively through the tree's leaves. Hourly measurements of the pot's weight were taken using a digital scale. Changes in the pot's weight indicate the amount of water evaporated, which corresponds to the water transpired by the tree through its vascular tissue.
Results and Discussion
The results showed that the sap-flow meter device slightly overestimates the tree's water consumption compared to the values obtained using the lysimetric method. Sap flow and transpiration follow a similar trend, both escalating throughout the day and reaching their highest levels in the early afternoon. This value reached 17.98 ml h-1 for sap flow and 16 ml h-1 for transpiration (by lysimetric method), followed by a rapid decrease in the late afternoon as the air cooled down. In addition, the results of device measurements showed that spraying water on the leaves lowers both the rate and volume of sap flow. When the canopy becomes wet, the evaporation of water from the leaf surface leads to a drop in the temperature, which in turn significantly slows down the flow of sap.
The v1/v2 ratio is not constant over time, making it crucial to choose the right starting point for measurements to ensure effective data acquisition during the device's operational cycle. It is essential to measure (by the device) the difference between temperature probes 40 seconds after heat pulse generation. The sap flow and transpiration followed a similar trend during the experiments. The sap flow and transpiration increased throughout the day, peaking in the early afternoon. On the first day, sap flow reached 17.98 ml h-1, while the second day recorded an even higher rate of 19.75 ml h-1. Correspondingly, the transpiration measured using the lysimetric method peaked at 16 ml h-1, followed by a rapid decline in the late afternoon.
Conclusion
The results obtained from the developed device indicate several key findings. Sap flow and transpiration exhibit a similar trend during the test period, with the estimated sap flow value being approximately 30% higher than that obtained using the lysimetric method. The device effectively demonstrated the impact of surface irrigation; spray irrigation influences the sap flow rate such that when the canopy becomes wet, the sap flow rate decreases significantly. Additionally, sap flow and transpiration are positively correlated with air and canopy temperatures, and negatively correlated with relative humidity. Following calibration, the results show that the heat pulse method can accurately and effectively measure sap flow in the vascular tissue of trees.

Biological and Biosystems Engineering

Synergistic Effect of Atmospheric Pressure Cold Plasma and Hydrogen Peroxide as an Efficient Approach for the Control of Citrus Postharvest Green Mold

Volume 14, Issue 4, Autumn 2024, Pages 355-366

https://doi.org/10.22067/jam.2023.82325.1165

E. Barzanouni, H. Sadrnia, F. Sohbatzadeh, S. Khodavaisy

Abstract Introduction
Penicillium Digitatum (PD) and Penicillium italicum diseases pose significant economic challenges to citrus fruit production across the globe. The primary aim of this research is to investigate the synergistic effects of low concentrations of H2O2 solution combined with transient spark discharge plasma on the inactivation of PD. Additionally, assess the chemical and physical properties. Ultimately, this approach can be presented as an eco-friendly solution for rinsing citrus fruits on an industrial scale.
Materials and Methods
The Penicillium digitatum (PD) isolate (ATCC 24692) was obtained from the Tehran Molecular Mycology Laboratory and cultured on Sabouraud Dextrose Agar medium at pH 5.6 and 27°C for 7 days. The initial concentration of spores in the solution was determined using a UV absorption spectrophotometer, set to 0.1 at a wavelength of 420 nm, and the concentration of spores was approximately equivalent to 106 spores per milliliter (Palou et al., 2002). In this study, the plasma reactor had a point-to-plane geometry. The high-voltage needle electrode was placed above a Petri dish filled with a microbial solution combined with H2O2, while the grounded electrode was immersed in the solution. The distance between the tip of the needle electrode and the surface of the solution was 15 mm. Solutions of 0.05%, 0.1% and 0.5%v/v H2O2 (35% soluble in water) were added to the microbial solution before plasma treatment. The final volume of the solution was 5 ml and exposure times were 2.5, 5, 10, and 15 minutes. The reactor was fed with an air flow of 2 l/min. A transient spark discharge was generated, characterized by a discharge voltage of approximately 18 kV, short durations of less than 100 ns, and high current pulses exceeding 1A, with a repetition frequency ranging from 0.5 to 10 kHz. After treatment, H2O2, NO2‾, and NO3‾ as the main long-lived species in plasma-activated solution are measured. Also, physical factors such as electrical conductivity and pH were measured. Data Analysis performed using SAS 9.4 software. 
Results and Discussion
With increasing plasma treatment time and H2O2 concentration, the log reduction increased across all treatments. The combination of 0.1 and 0.5% H2O2 solution with plasma resulted in complete inactivation of P. digitatum within just 15 minutes. In plasma-treated solutions, regarding chemical properties, the concentrations of H2O2, NO2‾, and NO3‾ increased linearly with the treatment time. Furthermore, the electrical conductivity increased linearly, with a notable acceleration in the treated 0.5% H2O2 solution, reaching 373µS cm-1. Additionally, pH value dropped from an initial value of 6.95, using distilled water as a control, to a low of 2.14 for plasma treated with 0.5% H2O2 after 15 min of exposure.
Conclusion
The combined treatment was more effective than the isolated use of hydrogen peroxide solution. H2O2 enhances the effectiveness of plsma sterilization without requiring additional power input. Consequently, the synergistic application of atmospheric pressure plasma and H2O2 proved to be a promising method for the inactivation of PD. The findings indicate that reactive oxygen species (ROS) significantly contribute to the inactivation of PD cells, as well as the concentration of H2O2. Finally, the combination of H2O2 solution at 0.1 and 0.5% with cold plasma presents an environmentally friendly method for sanitizing citrus fruits.
Acknowledgment 
This work was supported by the Ferdowsi University of Mashhad [Grant number 48527]. The authors greatly appreciate the technical support from Mazandaran University in Iran, particularly from the Department of Atomic and Molecular Physics. 

Biological and Biosystems Engineering

Investigating the Effect of Storage Time on the Mechanical Properties of Biodegradable Polylactic Acid Film Containing Zinc Oxide Nanoparticles

Volume 14, Issue 3, Summer 2024, Pages 283-299

https://doi.org/10.22067/jam.2023.81863.1160

N. Tajari, H. Sadrnia, F. Hosseini

Abstract Introduction
Polylactic acid (PLA) is a biodegradable polymer that can replace petroleum-based materials in packaging films due to its unique properties. However, sometimes the degradability of polymers can be considered a negative factor, such as when significant changes in the mechanical properties of the polymer occur during use. Another notable issue is the brittleness of polylactic acid, which can be modified to some extent by adding other materials. The addition of materials such as nanoparticles and plasticizers can improve the flexibility and mechanical properties of polymer films. Polymer films must possess acceptable physical, mechanical, thermal, and other relevant characteristics for use in the packaging industry. The acceptable level of these properties can be obtained by comparing them with the established standards for commonly used polymers in the industry. Low density polyethylene (LDPE) is a polymer widely used in the packaging industry, making it a good benchmark for comparison. This research focused on studying various factors affecting the quality of the produced films, including mechanical properties, light absorption, contact angle, and microstructures. Investigating the mechanical properties of the PLA films is crucial due to the polymer’s degradability over time. Polylactic acid films with different compounds containing PEG 400 and Tween 80 as plasticizers and ZnO nanoparticles were investigated for 14 months (in the first, second, third, fourth, and fourteenth months) in terms of mechanical properties. Finally, the obtained values were compared with standard values for packaging and their mechanical behavior was analyzed.
Materials and Methods
Experiments were performed in the post-harvest and central laboratories of Ferdowsi University of Mashhad, Iran. The films were prepared using the solvent casting method. First, PLA granules were dried for 24 hours at 60 °C and then 1 g of PLA in 50 ml of dichloromethane was dissolved at room temperature by magnetic stirring for 12 hours. ZnO nanoparticles, PEG 400 and Tween 80 were incorporated into PLA and DCM solution, 1 wt% PLA, 20 wt% PLA, and 0.25 wt% solution, respectively. To prepare films containing nanoparticles, nanoparticles and dichloromethane were sonicated with an ultrasonic probe for 10 minutes and then added to the base solution and stirred for one hour.
Mechanical properties of the samples were determined based on the ASTM D882-02 standard method. A texture analyzer (H5 KS, Manchester, U.K.) was used for this test. Light absorption was studied using a spectrophotometer (CAMSPECM550, UK). The contact angle of the samples was measured using a goniometer (model 200-00, Ramé-Hart Instrument Co, Succasunna, USA) in accordance with the ASTM D5946-04 standard. The surface morphology of the samples was visualized using scanning electron microscope (LMU TESCAN BRNO-Mira3, Czech Republic). The results were analyzed using Minitab software version 18 (Minitab Inc, USA) and the graphs were created in Microsoft Excel 2013.
Results and Discussion
The neat PLA film has a smooth surface, and with the addition of nanoparticles or plasticizers, the surfaces become uneven. The addition of nanoparticles and plasticizers caused more opacity of the film and better protection against ultraviolet rays. The presence of plasticizers, especially Tween 80, increased the hydrophilicity of the films. Packaging films should be flexible and have ductile behavior and the addition of plasticizers caused ductile behavior. However, Tween 80 was not able to create stable ductile behavior. The stress-strain diagram shows that most samples displayed ductile behavior over 14 months, except for the neat PLA film and the film containing Tween 80 and nanoparticles. The values of tensile strength, elastic modulus, and elongation at break for low density polyethylene have been reported as 11.7 MPa, 260.4 MPa, and 225%, respectively. The lowest value of tensile strength (18.56 MPa) and elastic modulus (1114.68 MPa) were related to P400/T80 film. This difference shows the acceptability of polylactic acid in the packaging industry. The elongation value is much lower than the standard, indicating the need to modify this parameter.
Conclusion
The research findings revealed a significant effect of film type on mechanical properties, as well as a remarkable impact of storage time on tensile strength and elongation at break. The effect of various factors such as changes in the texture of the film due to the presence of plasticizers or non-uniform distribution of nanoparticles makes it impossible to determine a consistent trend for the effect of time on the films. The elongation at break for the produced films was much lower than the standard, which still needs to be modified due to the importance and sensitivity of this parameter in packaging. Polylactic acid has high tensile strength and high elastic modulus. Therefore, it can be combined with other polymers, various plasticizers, or nanoparticles at higher percentage to improve flexibility. The presence of plasticizers and nanoparticles in the film substrate increased opacity and enhanced protection against ultraviolet rays. The produced films were more hydrophilic compared to low density polyethylene.
Acknowledgment
This research was supported by Ferdowsi University of Mashhad (Grant No. 54096). The authors would like to thank Dr. Mohammadreza Pajohi-Alamoti, Department of Food Hygiene and Quality Control, Bu-Ali Sina University, Hamedan, Iran for providing polylactic acid granules.

Biological and Biosystems Engineering

The Efficiency of Cold Plasma Treatment on Aspergillus Niger Disinfection and Quality Properties Preservation of Grapes during the Post-harvest Period

Volume 14, Issue 3, Summer 2024, Pages 337-353

https://doi.org/10.22067/jam.2023.84550.1191

A. Khalaj, E. Ahmadi, S. Mirzaei, F. Ghaemizadeh, R. Abbaszadeh

Abstract Introduction
Grape is a major horticultural crop with a high nutritional value in the world. The optimal geographic and climatic conditions in Iran have positioned it as one of the most important regions for grape cultivation in the world. Black rot, caused by Aspergillus niger, is a highly destructive fungal disease that affects the grapes by targeting wounded areas. It causes crushing of the grapes, the falling of berries, and reduces transportation and storage properties (Ponsone et al., 2011). Various methods, such as fumigating bunches with sulfur dioxide and storing them in a modified atmosphere, have been used to control fungal rot and prolong the shelf life of grapes. However, each method has its limitations. Grape fumigation with sulfur gas is harmful to human health (Duarte-Sierra et al., 2016) and the efficiency of modified atmospheric storage on rot control and maintaining the quality of grapes depends on the type of variety, storage temperature, and especially gas concentration (Himelrick, 2003).
Given the lack of efficiency in traditional methods, it is imperative to introduce modern techniques that can effectively disinfect microorganisms. These advanced methods offer several advantages, including the preservation of crop quality, an increase in crop shelf life, the promotion of good health, and substantial economic benefits. A technique of this type includes using non-thermal (cold) plasma (NTP) technology to eliminate food microorganisms (Bourke et al., 2018). The effect of cold plasma at atmospheric pressure on the reduction of bacterial populations in food products such as lettuce, tomato, strawberry, and cherry tomato has been reported (Bermúdez-Aguirre et al., 2013; Pasquali et al., 2016; Ziuzina et al., 2014). Research has shown that cold plasma can effectively inactivate Aspergillus in various orchard and agricultural products (Butscher et al., 2016; Ghorashi et al., 2020; Selcuk et al., 2008). The effect of cold plasma on the quality characteristics of the product during the post-harvest period has also been investigated. Blueberries treated with cold plasma for less than 15 minutes showed remarkable results: after 10 days, the fruit exhibited reduced lipid peroxidation and darkening, with no impact on the total anthocyanin content, pH, or firmness of the product (Hu et al., 2021). In a study by Rana et al. (2020), it was found that subjecting strawberries to 15 minutes of cold plasma with packaging after 5 days of storage at 25°C had no significant impact on pH, TSS, and moisture content of the fruit.
The review of the literature reveals the absence of research on fungal disease control and grape quality evaluation following the use of NTP. This study aims to investigate the efficiency of plasma treatment in reducing the infection with Aspergillus fungi, along with examining the physical, chemical, and mechanical properties of Fakhri grape.
Materials and Methods
This research was conducted as a completely randomized design in a factorial experiment at four plasma levels (0, 10, 20, and 40 s) and five storage periods (1, 2, 3, 4, and 5 weeks) with three replications at 4°C.  A plasma generator was first designed and manufactured in this study. A specifically designed and fabricated plasma application probe was also developed for grape berries. The individual grape berries were then sterilized with 1% sodium hypochlorite under a laminar hood for 2 minutes. Afterward, they were rinsed three times with sterile distilled water to remove any remaining disinfectant residue from their surfaces. Sterilized berries were immersed in Aspergillus spore suspension with 105 spores.ml-1 concentration. Finally, all samples were dried on paper filters and prepared for different plasma treatment durations (0, 10, 20, and 40 s). The treated samples were stored at 4°C, and the infection percentage and microbial load were measured on a weekly basis. To assess the preservation quality, chemical parameters such as pH, TSS, and TA, physical parameters (color change and weight loss), and mechanical properties were measured every week. Additionally, thermal imaging was performed weekly.
Results and Discussion
Plasma application during storage significantly reduced the infection percentage and microbial load in Aspergillus-inoculated samples. At the end of the storage period, the infection percentage and microbial load in the 40-second plasma treatment were 5% and 2.5 CFU g-1 respectively, while in the control group, the infection percentage was 100% and the microbial load was 4 CFU g-1. At the end of the storage period, the lowest pH level in the plasma was observed for 40 s plasma. This could be attributed to effective contamination control, as fungal contamination leads to alkalization of the environment. The highest amount of TSS was also observed in control and 40 s plasma. But in the 10 and 20 s plasma treatment, the process of changes was gradual and not significant. The higher TSS level of control and 40 s plasma can be due to the weight loss caused by the spread of contamination and moisture leakage caused by damage to the tissue. This decrease in moisture leads to an apparent increase in the TSS index. Research has shown that plasma primarily affects the surface characteristics of products, and when applied with the appropriate voltage and duration, it does not alter the internal chemical properties (Hu et al., 2021). Over time, weight loss increased in all treatments. This increasing trend during the storage period is higher in control and 40 s plasma compared to 10 and 20 s plasma. Therefore, the weight loss in the control can be due to the spread of contamination and aging of the product over time. However, the weight loss in the 40-second plasma treatment can be due to the destruction of the fruit tissue caused by longer duration of the plasma application.
In the current research, by increasing the duration of plasma application to 40 s, a significant decrease in L*, a*, and b* indices and an overall change in the color of the product was observed. Research shows that in blueberries, inappropriate duration of plasma treatment causes the loss of wax on the fruit surface and leads to darkening of the product (Hu et al., 2021). The highest and lowest changes in temperature drop were observed in the control treatment (5°C) and 10 and 20 s plasma (3 and 3.5°C, respectively). According to research, an increase in fungal contamination leads to a decrease in humidity, increases weight loss, and subsequently a decrease in product temperature. A decline in mechanical characteristics was noted for the control and plasma treated samples during the storage period. The lowest value for indicators was observed in the 40 s plasma treatment. However, no significant difference was observed in samples treated with plasma for less than 20 seconds compared to the control group up to the middle of the storage period. According to a report by Misra et al. (2014), plasma application can reduce tissue softness. Therefore, optimizing its plasma duration and intensity is very important (Pan et al., 2021).
 Conclusion
Our experiments aimed to investigate the effect of NTP treatment on controlling Aspergillus infections while preserving the quality properties of Fakhri grapes. The obtained results are important for two main reasons. Firstly, an innovative probe was designed for plasma applications, specifically tailored to the shape and size of individual grapes in order to thoroughly cover them with plasma. Secondly, application of plasma was carried out for the first time and yielded valuable results, indicating that this technique can control fungal infections and preserve the chemical, physical, and mechanical properties of grapes.

Biological and Biosystems Engineering

Cold Plasma Technique in Controlling Contamination and Improving the Physiological Processes of Cereal Grains (a Review)

Volume 14, Issue 1, Winter 2024, Pages 83-104

https://doi.org/10.22067/jam.2023.84647.1193

M. Pourbagher, R. Pourbagher, M. H. Abbaspour-Fard

Abstract Today, almost half of the total human food, especially in Asia, is directly supplied from grains, and nearly 70% of the cultivated area of the world, which is one billion hectares, is used for growing grains. Therefore, non-destructive methods must be found and developed to increase seed quality in agriculture and industry. Cold plasma is a novel and efficient method that can be used in the agricultural and food sectors for the inactivation of surface microorganisms and the excitation of seeds. This review presents a summary of the effectiveness of cold plasma treatment on the characteristics of four important cereal plants: wheat, rice, corn, and barley. The focus is on the effects of this treatment on seed germination, surface property changes, water uptake of seeds, growth parameters of root, shoot, and seedling length, biomass parameters, and metabolic activities. By examining the research conducted by the researchers, it can be seen that the cereal seeds treated with cold plasma had better germination power, water absorption, shoot length, growth efficiency, shoot and root weight, and metabolic activity. This review can provide insight into the promising trends in utilizing plasma as a method to decrease the prevalence of harmful plant diseases transmitted through seeds and reduce the dormancy of hard seeds.

Biological and Biosystems Engineering

Evaluation of Mechanical and Chemical Parameters of Okra with Chitosan Coating in Nano Packaging Films and Atmospheric Modified Conditions

Volume 12, Issue 4, Autumn 2022, Pages 600-612

https://doi.org/10.22067/jam.2021.69257.1027

A. Heydarian, E. Ahmadi, F. Dashti, A. Normohammadi

Abstract Introduction
The quick deterioration of fruit and vegetables has led researchers to find a solution to increase the shelf life. Foodstuff packaging is a vital technology to maintain freshness, prevent deterioration, and physiological and mechanical damages, and increase the shelf life of fresh products. Employing various post-harvest technologies prevent light, heat, and humidity transmission and control the microorganism activity, thereby reducing the cost and maintaining the quality of fresh and processed products during storage. Fresh okra has a shelf life of 10 days and is stored at 1-10°C due to high respiration rate and moisture loss. Today, the use of nanotechnology in the packaging industry is developed and expanded. The aim of the packaging is to increase the shelf life and prevent bacterial and shipping damages, as well as control the humidity and gases transmission, thereby reducing food spoilage. Modified atmospheric packaging (MAP) is one of the famous methods for increasing the shelf life of fresh products in which the aging process is reduced by increasing CO2 and decreasing. Decreasing the respiration rate, producing ethylene, and metabolic reactions in the modified atmosphere lead to a reduction in product deterioration. The use of coatings and edible films is being increased in order to maintain sensitive features like flavors, fragrances, and the appearance of different products and increase the shelf time of fruits and vegetables. Chitosan edible coating is a non-fragrance and non-flavor polysaccharide with a high molecular weight that is widely used because of its antifungal, biological, and biochemical properties. Chitosan is a natural polymer obtained from chitin, which is abundantly found in crustacean shells. The aim of the present study is to evaluate the effect of packaging films and chitosan coating under the modified atmosphere storage condition on qualitative and quantitative parameters of okra during storage.
Materials and Methods
The process of present research was performed in the Laboratory of Mechanical Properties and Rheology of the Biosystem Engineering Department, Faculty of Agriculture, Bu-Ali Sina University, Hamedan, in 2016. Okra cv. Kano Dwarf was selected due to its short post-harvest life and provided by farms in Kermanshah Province. Okras were handpicked and they were free of any spots, contamination, or decay, with the almost same size and shape, without any mechanical and microbial damage. The treatments of the present study were chitosan covering, modified atmosphere by a gas mixture of 5% O2 + 10 CO2 + 85% N2, three types of packaging films including silicone nano-emulsion (Nano Bespar Aytak Co.), nano-polyethylene, and light polyethylene (LFO200), as well as two temperature levels of 1 ± 4°C (refrigerator) and 1 ± 25°C (room temperature). The influence of modified atmospheric treatments, chitosan coatings, and packaging films at two storage temperatures on chemical factors (pH and TSS) and mechanical properties including shear stress (TB), shear force (FB), shear modulus (GK) were evaluated at the end of 12 days of storage in a completely randomized design with a factorial experiment in three replications on Okra.
Results and Discussion
Among the films used, silicon nano emulsion film and chitosan coating were more able to maintain TSS. The pH value decreased due to the control of respiratory rate and corruption under modified atmospheric conditions. The mechanical properties of the samples showed that the shear stress changes of the coated sample were significantly less than the untreated ones compared to the beginning of the maintenance period. The sample stored at 4°C had less shear force during the storage period than similar specimens at 25°C. The modified atmosphere caused the shear modulus to decrease with increasing storage time compared to the beginning of the storage period.
Conclusion
The results of the present research revealed that silicon nano-emulsion film has a higher capability in preserving the qualitative and quantitative properties of okra compared to other studied films. Between the two studied temperatures, 4°C storage temperature had better performance in preserving qualitative and quantitative properties of the okra compared to 25°C. The controlled atmosphere increases okra's shelf life due to reduced respiration rate. In general, maintenance of the products in a modified atmosphere package preserves the quality of the products and extends their shelf life.

Biological and Biosystems Engineering

Microscopic Investigation of Cold Plasma Effect on Chickpea Seed Germination

Volume 12, Issue 2, Spring 2022, Pages 231-240

https://doi.org/10.22067/jam.v12i2.88718

M. Fereydoni, H. Haji Agha Alizadeh

Abstract Introduction
As the world's population grows, more food need to be produced. Plasma technology is one of the methods that can improve plant growth. Cold plasma is effective in increasing growth and germination indices. In this article, the effect of cold plasma based on corona discharge was investigated on germination of Adel, Mansur, and Azad chickpea varieties.
Materials and Methods
In the corona discharge method, a relative vacuum should be used. Corona discharge is formed when there are pronounced spatial in-homogeneities in the electric field, in particular, when the electric field exceeds the breakdown threshold in a limited spatial region. This commonly occurs when highly asymmetric electrodes are employed, such as a point and a plane. Thermodynamically corona is a very non-equilibrium process, creating a non-thermal plasma. The avalanche mechanism does not release enough energy to heat the gas in the corona region generally and ionize it, as occurs in an electric arc or spark. Only a small number of gas molecules take part in the electron avalanches and are ionized, having energies close to the ionization energy of 1- 3 ev, the rest of the surrounding gas is close to ambient temperature. Corona discharge is a weakly ionized non-equilibrium plasma based on the avalanche mechanism. If it reaches a close distance with a conductive material or increase the electrical field, it can create longer breakdown streamers and eventually create sparks. The system is designed to convert 220V voltage with a frequency of 50 Hz to 12 kV voltage with a frequency of 9 kHz. Two electrodes with a 2 cm distance are in a vacuum chamber with a negative pressure of 20 pounds per square inch. And the samples are placed between two electrodes. Experiment was performed in form of a.factorial experimental design based on a CRD. In this plan, treatments are randomly placed in experimental units. The type of factorial experiment performed is 3×3×2×2 and multiplied numbers are factor levels. Seed production year factor in two levels, moisture factor in two levels, Seed variety factor in three levels, and exposure duration factor in three levels were examined. Plasma-exposed seeds and non-exposed seeds were grown under the same conditions. The samples were selected completely randomly. The samples were wetted 24 hours before exposure. Then all 18 chickpeas were placed in a dish in order to observe proper repetition. Samples from each dish were exposed to cold plasma under the same conditions between samples for a specified period of time. After exposing the samples to cold plasma, samples of all dishes under the same conditions at 30 °C and 300 lux environmental light were examined for germination evaluation. For this purpose, samples of each dish were placed in a cover of cotton cloth. They got wet every 4 hours. After 48 hours, all samples were examined and the root length of each sample was measured.
Results and Discussion
The results showed that seeds exposed to plasma for 60 seconds had a faster germination speed than those without exposure. Also, seeds that were exposed to plasma for 30 seconds had a longer root length than those without exposure. According to the results of statistical analysis, exposure to cold plasma for 30 seconds has increased root length in Adel chickpea variety up to 12.5% and in Mansour variety up to 18%.
Conclusion
After statistical analysis, appear that root length under the same conditions, during 30 seconds of exposure to cold plasma, is significant at 5% level from non-exposure and 60 seconds of exposure. Microscopic images of samples were examined on the outer surface and inner tissue of seed cell. Studies have shown that the outer surfaces of seeds exposed to cold plasma are smoother, less prominent and smaller contact angle than those without exposure to plasma. This change can increase the hydrophilicity of seeds. But cold plasma had no effect on cell tissue in terms of size and number.

Biological and Biosystems Engineering

Investigation on the Capability of GreenSeeker Sensor in Predicting Nitrogen Status and Fractional Vegetation Cover of Spinach Crop

Volume 12, Issue 1, Winter 2022, Pages 95-106

https://doi.org/10.22067/jam.2021.68387.1013

M. Hashemi Jozani, H. Bagherpour, J. Hamzei

Abstract Fractional vegetation cover (FVC) and normalized difference vegetation index (NDVI) are the most important indicators of greenness and have a strong correlation with green biomass. The objective of this study was to evaluate a hand-held GreesnSeeker (GS) active remote sensing instrument to estimate NDVI and FVC in the spinach plant. In this study, the color indices of the G-B index and Excess Green (ExG) were used as color vegetation indices to discriminate leaves from soil background. During 28 to 44 days after emergence (DAG), the results showed good correlations between chlorophyll yield and NDVI (R = 0.61 to 0.91), and the correlation between NDVI of GS and biomass was significant. In addition, in this growth stage, the results showed a good coefficient of correlation between NDVI of GS and FVC (R = 0.67 to 0.82). In assessing the nitrogen rate on the NDVI of GS, the results showed significant differences only at the short period of growth stage (28 to 36 DAG). The results revealed that GreenSeeker performed well for estimation both chlorophyll and biomass yield of spinach crop and it could be used as a suitable instrument for estimation of leaf area index in the middle of the plant growth period.

Biological and Biosystems Engineering

Studying some Pollutant Emissions of an Injection Gasoline Engine Using Mixed Fuel of Ethanol, Gasoline and Carbon Nanoparticles

Volume 11, Issue 2, 2021, Pages 213-230

https://doi.org/10.22067/jam.v11i2.76903

M. Malek mohammadi, M. Rahnama, S. Abdanan Mehdizadeh, N. Kazemi

Abstract Introduction
Due to the rapid growth in the urban population, the numbers of cars also have increased which resulted in an increase of pollution level in the urban areas of the developing countries. The pollutants emerging from combustion engines may include: carbon monoxide (CO), unburned hydrocarbons (UBHC), oxide of nitrogen (NOx), oxides of sulfur (SOx), particulate matter (PM), soot, hydrogen, oxygen, traces of aldehydes, alcohols, ketons, phenols, acid, lead aerosol, etc., along with normal combustion products i.e. carbon dioxide (CO2) and water vapors. In order to overcome the problems associated with the bio-fuel, the chemical substances like fuel additives derived from organic, inorganic metals were used. Fuel additives generally improve the combustion efficiency and reduce the pollution. Metallic based compounds, such as manganese, iron, copper, barium, calcium and platinum, etc., which have been used as a combustion catalyst for hydrocarbon fuels. Recent advances in nanoscience and nanotechnology enables production, control and characterization of nanoscale energetic materials. Nano materials are more effective than bulk materials because of its higher surface area. Another important advantage of nanoparticle is its size, because there is no chance for fuel injector and filter clogging as in the case of micron sized particles. Gan and Qiao, (2011) investigated the burning characteristics of fuel droplets containing nano and micron sized aluminum (Al) particles by varying its size, surfactant concentration and type of base fluid. Tyagi et al. (2008) conducted a study to improve the ignition properties of diesel fuel and investigated the influence of size and quantity of Al and Al2O3 nanoparticles in a diesel fuel. It was inferred that it shortens the ignition delay and increased the ignition probability of fuel. Finally, it was concluded that, the increase in heat and mass transfer properties of the fuel has the potential of reducing the evaporation time of droplets. In the present investigation, the effect of mixture of ethanol with gasoline and carbon nanotubes on emission characteristics was evaluated using Jatropha biodiesel in a compression in a spark ignition engine.

Materials and Methods
In this study, a mixture of ethanol with gasoline (at five levels, 0, 10, 20, 30 and 40%) as a renewable fuel and carbon nanoparticles (at three levels of 0, 20 and 80 ppm) as catalyst were used in spark ignition engine (in 1000, 2000 and 3000 rpm). Engine pollutants such as sound, carbon monoxide, unburnt hydrocarbons, carbon dioxide and oxygen output were measured. Furthermore, a device was designed and manufactured to measure and display the amount of carbon monoxide in the exhaust outlet; moreover, if the amount of carbon increased air compressor was activated to reduce carbon monoxide in the exhaust outlet.

Results and Discussion
The results showed that with increasing ethanol consumption, the amount of carbon monoxide and unburned hydrocarbons were reduced. Furthermore, the amount of produced oxygen and carbon dioxide increased. Also adding carbon nanoparticles to fuel caused the engine sound level decreased. According to the observation, carbon monoxide decreased while using an electronic device compare to the engine without a carbon monoxide controlling system. This depicts that implementation of carbon monoxide can be control and reduce which is very useful while engine is working under the close environments.

Conclusion
The use of alternative fuel, gasoline as well as the reduction of exhaust emissions in the spark ignition engine is of great importance. Therefore, in the present study five levels of ethanol (0, 10, 20, 30 and 40%) and three levels of carbon nanoparticles (0, 20 and 80 ppm) were mixed with gasoline and used in spark ignition engine at three rotation speed (in 1000, 2000 and 3000 rpm). According to the results, there is a reduction in carbon monoxide and unburned hydrocarbons and increasing carbon dioxide emission by using ethanol, because of its fuel bound O2. Furthermore, 3.8% dB 54% reduction in sound and CO, respectively at 3000 rpm with E10 were observed.

Biological and Biosystems Engineering

Effect of Pomegranate Seed Oil Encapsulated in Chitosan-capric Acid Nanogels Incorporating Thyme Essential Oil on Physicomechanical and Structural Properties of Jelly Candy

Volume 11, Issue 1, 2021, Pages 55-70

https://doi.org/10.22067/jam.v11i1.84882

H. Mirzaee Moghaddam, A. Rajaei

Abstract Pomegranate seed oil (PSO) is a well-known source of valuable compounds. The aim of this study was to investigate physicomechanical and structural properties of jelly candy enriched with PSO encapsulated in chitosan (CS)-capric acid (CA) nanogel incorporating thyme essentioal oil (TEO). For this purpose, initially the CS-CA nanogels were produced by creating amide bondes between CS and CA, which Scanning Electron Microscope (SEM) image showed the spherical form of CS-CA nanogels. Then, PSO-in-water Pickering emulsions were stabilized with the CS-CA nanogels as well as the CS-CA nanogels incorporating TEO. The results showed that the presence of TEO in the nanogel structure caused smaller oil droplets. Then, Pickering emulsions were used in the formulation of jelly candy and subsequently the microscopic structure, texture profile analysis (TPA) and color indexes of jelly candies were studied. The use of PSO in the encapsulated form reduced the separation of the PSO from the texture of the jelly candy. The results of TPA showed that although the samples containing PSO in the encapsulated form had lower hardness (156.6-173.4 N), gumminess (202.2-262.1 N), cohesiveness (1.3-1.5%), resilience (40.2-54.7 N.s) and adhesiveness (0.29-0.4 N.s) than the control (250.3 N, 627.9 N, 2.14%, 160.7 N.s, 0.63 N.s), their springiness (0.92-0.93%) was higher than the control (0.79%). Moreover, the color indexes showed that the samples containing PSO in the encapsulated form changed the color indexes more than the control, which was more in the presence of TEO.

Biological and Biosystems Engineering

Investigating the Impact of the Magnetized Water on the Growth and Germination of Five Wheat Grain Seeds

Volume 10, Issue 2, 2020, Pages 289-298

https://doi.org/10.22067/jam.v10i2.76707

S. Zarei, M. Kasraei, M. A. Nematollahi

Abstract Introduction
Cereals as one of the most important sources of food plants could provide more than 70% of the food for the human population. Passing of water from the magnetic field is among approachable methods in order to reduce the total amount of water used for irrigation. Moreover, magnetized water is a new concept for increasing the water efficiency. Therefore, this study was aimed to investigate the effects of the magnetized water on some of features containing dry weight, germination velocity and percentage, length and weight vigor indices of five common wheat cultivars including Roshan, Sardari, Shiraz, Falat and Yavarus, to introduce the best cultivar considering the growth and germination indices as well as water and energy efficiency.
Materials and Methods
To perform this experiment, a device with a magnetic field of 500 millitesla was constructed to accommodate both the water path and the placement of seeds in the magnetic field. To perform the experiments, 10 seeds in 4-kg vases and 25 seeds in each Petri dish were cultivated in the greenhouse and laboratory, respectively. The experiments were carried out in the form of completely randomized factorial design. The factors are considered as the duration time of keeping the water in the magnetic field (three levels of 30, 60 and 120 minutes), the intensity of the magnetic field (three levels of 100, 150, and 200 millitesla), and five wheat cultivars (Roshan, Sardari, Shiraz, Falat and Yavarus) in three replications.
Experiments related to the both of rate and percent of germination and for dry weight were performed at room temperature in the laboratory and greenhouse under controlled conditions, respectively. The measured data were analyzed using SAS software. The F test was used to determine the significant level of treatments. The comparison of the means was evaluated using LSD test.
 Results and Discussion
The obtained results, showed that the effect of magnetic water on all growth and germination indices compared to control samples was significant. Under the 150 millitesla and 120 minutes treatment, the Yavarus, Roshan and Sardari cultivar had maximum dry weight, respectively. The Roshan cultivar had the maximum germination velocity at 100 and 150 millitesla and duration time of 30 minutes. Moreover, the maximum germination percentage was found in the Roshan cultivar, which did not have a significant difference with Yavarus cultivar. The Roshan cultivar in 200 millitesla field and duration time of 60 minutes, had the maximum percentage of length vigor index, which showed a significant difference with other averages.
In general, Roshan and Sardari cultivars had more length vigor index than other cultivars. Sardari cultivar had maximum percentage of weight vigor index under 200 millitesla and 120 minutes duration time, which had no significant difference with the percentage of weight vigor index at the same field level and with duration time of 60 minutes.
Conclusion
According to the obtained results to achieve the maximum value of dry weight, it is better to use the Yavarus cultivar. It is recommended to use the Roshan cultivar with the lower level of magnetic field and duration time to attain the maximum value of the germination velocity and percentage. To get the maximum value of the length vigor index and the weight vigor index the Roshan and Sardari cultivars, and the Sardari cultivar with field of 200 milli Tesla and lower duration time are preferred.

Biological and Biosystems Engineering

Design, Fabrication and Evaluation of a Novel System for Magnetic Field Application to the Seeds- Case study of Onion Seed

Volume 10, Issue 1, 2020, Pages 1-10

https://doi.org/10.22067/jam.v10i1.76370

S. Rezaei, M. Dowlati, R. Abbaszadeh

Abstract Non-chemical treatments are an approach for improving seed germination. In order to evaluate the effects of the magnetic field application on onion seed germination and seedling growth indices, a quadrupole magnetic field system was designed and fabricated. It was also compared with a dipole magnetic field system. In the quadrupole system, each coil consisted of three layers and the cores were moved inside the coils. These arrangements make it possible to change the magnetic field intensity in addition to input current setting. The experiments were conducted based on factors including the type of system (bipolar and quadrupole), magnetic flux density (75, 150, 300 and 600 μT) and duration of the field application (15, 30, 60 and 120 min). Germination percentage, germination rate, mean germination time, seedling vigor index, shoot length, root length, fresh weight of shoot and root, fresh weight of seedling, dry weight of shoot and root were measured. The results showed significant effects on seed germination and seedling growth of onion. In most germination characteristics, the quadrupole system had a better impact than the bipolar system. For many traits (except for weights), the increase in field intensity degraded the traits. Quadrupole system that applied the magnetic field of 600 μT for 15 minutes, yielded 63% increase in the total seedling weight. Most of the germination traits were not affected by exposure time. Further investigations are required for shorter exposure times compared to used durations in this study.

Biological and Biosystems Engineering

Structural and Performance Evaluation of a Pollen-duster, Designed for Date Farms

Volume 9, Issue 2, 2019, Pages 427-438

https://doi.org/10.22067/jam.v9i2.68916

F. Akhavan, S. Kamgar, A. A. Golneshan

Abstract Introduction
Pollinating elevated date palms has been a challenging problem for many years. A few types of equipment have been designed and manufactured in the last fifty years, using either low pressure or compressed air to overcome this problem. However traditional pollination is still the most popular method in none-mechanized and small date farms. In the present research, a light portable electrical pollen-duster has been developed and tested.
Materials and Methods
A powerful ducted fan, equipped with a speed controller and a servo tester was made and installed on the top of a 6 -7.7m long carbon fiber boom, to provide a high volume rate of air flow for pollination. A small part of air flow is conducted through a by-pass tube to hit the pollen/pollen-flour blend in the pollen bin and suspend it. The rest of air flow, passing through a venturi, is responsible to provide a relative vacuum at the opening of pollen bin to pull up the suspended pollen and throw it toward the date palm crown. Although plain flour is traditionally used as filler in mechanical pollinators, however, SEM imaging showed that pasta flour particles are bigger than plain flour particles and are closer in size to pollen particles. Also, Repose angle of date pollen was measured as 38º where plain flour and pasta flour showed 44.9º and 40.7º respectively (figures 6 and 7). So, Pasta flour was used instead of plain flour to make a blend.
To provide a low-weight pollen-duster, wires extending from ducted fan to its actuating equipment (battery, servo tester, and speed controller) were selected to be a combination of 2.5mm2 (3 meters) and 1.5mm2 (3 meters) types in the standard boom. This lowered the applied force on the operator’s hand by 33% (Figure 5 and equations 4 and 5).
Evaluation of the pollen-duster has been performed in Khoor town in Isfahan province of Iran. Eighteen trees of Kabkab variety were pollinated in a completely random test with 6 treatments (five mechanical treatments compared with traditional treatment). Mechanical treatments were using 0.5, 1.5 and 2.5g pure pollen and 2 and 6g pollen-flour blend (in 1:3 ratio) in each of the three weekly repetitions. After 8 weeks, in kimri stage, normal, abnormal (non- pollinated), and dropped fruits on some randomly selected strands were counted to determine pollination as well as fruit setting efficiencies. Fruits weight in each treatment was measured on some random fruits in the Tamar stage. A new index; called "pollen consumption index", was introduced to provide a measure of pollen consumption rate in order to prevent redundant pollen consumption which has no sensible effect on the yield.  
Results and Discussion
Calculated pollination and fruit setting efficiencies did not show a significant difference in all treatments, convincing that the traditional method could be replaced by pollen-duster without any yield difference. It offers benefits of lower pollen consumption; more trees pollinated in a day and also safer pollination due to reducing number of trees climbing. It was also shown that a tree could be pollinated properly with 0.5g pollen, so each hectare of date farm (120 trees) needs almost 180g pollen for all three replications, almost 1/4 of Perkins consumption report and 1/3 of Mostaan for three replications. Fruits weights of two pollen-flour treatments were significantly lower than others. As there is not any report available on the effect of the presence of flour or concentration of pollen on date fruits weights, so with the available data no definite reasoning can be made.
Conclusion
The developed pollen-duster could be used instead of the traditional date palm pollination method with the same fruit set and lower pollen consumption. The weight of the fruits in pollen-flour treatments `was lower than pure pollen and traditional treatments.

Biological and Biosystems Engineering

Analysis of Microscopic Image Textural Features of Artichoke Leaf Extract Powder Produced from Vacuum Spray Drying

Volume 8, Issue 2, 2018, Pages 295-308

https://doi.org/10.22067/jam.v8i2.63321

S. Sadeghzade Namavar, J. Amiri Parian, R. Amiri Chayjan

Abstract Introduction
The artichoke is part of the foods from the vegetable group that provide important nutrients like vitamin A and C, potassium and fiber which used as a food and medicine. In the pharmaceutical sector, dried extracts are used in the preparation of pills and capsules. Dried extracts can be prepared from the dehydration of a concentrated extractive solution from herbal materials (leaves, roots, seeds, etc.), resulting in a dried powder. The spray drying is widely used in the preparation of dried powders from extracts of medicinal plants, fruit pulps. One of the newly developed spray drying techniques is an ultrasonic vacuum method, which strengths of spray drying by incorporation of ultrasonic atomizer and vacuum chamber. Nowadays, image processing has been applied to food images, as acquired by different microscopic systems, to obtain numerical data about the morphology and microstructure of the analyzed foods. For this purpose, microscopy and image processing techniques could be considered as proper tools to evaluate qualitatively and quantitatively the food microstructure, making possible to carry out numerical correlations between microstructure data, as obtained from the images, and the textural properties of food powders. The textural characteristics of the obtained dried powders are determined by means of a perfect detection by scanning electron microscopy (SEM) pictures, and analyzed with a statistical approach for image texture studies, which calls the gray level co-occurrence matrix (GLCM) technique. The object of this study was to illustrate the application of image processing to the study of texture properties from extract powder using GLCM texture analysis and some vacuum spray dryer conditions effect on the texture features of mass particles and single particle SEM images.

Materials and Methods
After preparing water extract solution from artichoke leaves, extracts were dried under four conditions of vacuum spray drying (according to Table 1). To study the texture of the obtained dried extract powders, different representative features are extracted from the GLCM matrix. The angular second moment (ASM), which is defined as a measure of the homogeneity of the image, the contrast parameter (CT), which represents the amount of local variations given by differences in the gray values in the image. The correlation value (CR), which is a measure of gray tone linear dependencies in the image depending on the direction of the measure (different θs). The inverse difference moment value (IDM), which, similar to ASM, quantifies the homogeneity of the image, however, using a different equation, the entropy parameter (ET), which is a measure that is inversely related to the order given by the gray tones in the image. Rangefilt and stdfilt calculates the local range and local standard deviation of an image respectively. Entropyfilt calculates the local entropy of a grayscale image also. Parameters (ASM, CT, CR and IDM were analyzed in four directions (0º, 45º, 90º, and 135º).
Results and Discussion
The results of analysis of variance showed that, the difference between the textural features of a single particle and mass particles in four different conditions vacuum spray dryer was significant statistically. Texture analysis was demonstrated that larger ASM, CR, and IDM values indicate less roughness, whereas larger CT and ET values indicate more roughness. At lower inlet temperature and higher vacuum pressure, water diffusion in the material to be slower and allowing the deformation process in the particles to be more pronounced. Consequently, it was possible to observe that generated smaller particles are rougher and less spherical. When the concentration is increased, due to the constant concentration of the additive, the ratio of excipient (lactose) to extraction decreased, as a result were formed a greater number of particles with rougher surfaces. According to these conditions, the values of CT, ET, rangefilt and stdfilt were larger while ASM, CR, and IDM values were smaller. By analyzing the effect of the angle on the oriented textural characteristics, the contrast and correlation parameter were maximum at the angles of 45 and 135 degrees and 0 and 90 degrees respectively.

Conclusion
Image processing could be auxiliary tools for understanding and characterizing complex systems such as food and biological materials. In this study imaging-based technique was developed to evaluate the texture properties of artichoke leaf extract powder at different conditions of vacuum spray drying. The use of higher temperatures and lower vacuum pressures contributed to faster evaporation rate and production of smoother and larger particles, thereby increasing ASM, CR, and IDM values and reducing CT, ET, Rangefilt and stdfilt. Furthermore, the contrast and entropy parameters showed inverse trends in comparison with correlation, energy and homogeneity. Decrease of solution concentration resulted in the more presence of lactose in the composition of extract/excipient improves the textural properties of powders. The direction parameter had also affected on GLCM textural features. Two oriented textural characteristics (contrast and correlation) also showed significant differences with respect to the nature of particle texture in different directions of measurement. The obtained data extracted from image analysis may provide valuable information to understand the role of structure with respect to product functionality.

Biological and Biosystems Engineering

Micromechanical Behavior of Potato Tissue by Scanning Electron Microscopy: Effect of Storage Time, Impact Energy and Curvature Radius of Impact Location

Volume 8, Issue 2, 2018, Pages 347-363

https://doi.org/10.22067/jam.v8i2.62599

S. Youneji, E. Ahmadi, A. Alavi Nia

Abstract Introduction
The mechanical impacts occur mainly during harvesting and post-harvesting operations, lead to the breaking of cell membranes in cellular structure that dependS on impact intensity. Furthermore, turgor pressure of potato tissue is influenced by the micromechanical and the physiological changes in the storage duration. Micromechanical changes of potato tissue due to the mechanical impact need to be monitored by microscopic images during storage. Scanning electron microscopy (SEM) is a high-resolution technique used to investigate the micromechanical behavior of potato tissue.

Materials and Methods
Potato samples (‘Sante’ cultivar), were stored at 5 ± 0.5°C and 85% relative humidity for 16 weeks. By 2-week intervals, potatoes were removed from the storage and then the impact test was done. Experimental factors were impacted energy at three levels of control (no impact was done), impact energy 1 (0.031 ± 0.002 J) and impact energy 2 (0.320± 0.020 J) and the radius of curvature at two levels of (35 and 45 mm). Water content was measured by drying thin slab samples in an oven at 70°C to a constant weight. The cell turgor pressure of potato tissue at 2-week intervals was estimated from the linear regression between turgor values of each mannitol solution (0–0.6 M) and relative volume change. The microstructural changes of impact location on the potato tubers were analyzed by SEM images at 2-week intervals during storage period. The surface and depth sections cutting from the impact location were immediately immersed in 2.5% glutaraldehyde in 0.1 M sodium phosphate buffer (2 h) at 4± 0.5°C. The specimens were then rinsed 3 × 10 min in 0.1 M sodium phosphate buffer (pH 7.2), and dehydrated through an ethanol series, 25, 50, 70, 90 and 100% dry, 15 min each step, 2 × 100%. In this study the HMDS as a high-quality chemical drying was investigated. The sample preparation for SEM observation then followed by chemical drying via HMDS, under a laboratory hood overnight. Analysis of variance test based on completely randomized design (CRD) was considered for all of the data using SPSS 23.

Results and Discussion
Superior preservation of potato microstructure was obtained by hexamethyldisilazane (HMDS) drying during sample preparation for SEM observation. The MIP software was used for quantitative analysis of SEM images and the microstructural features of potato tissue at the impact location were determined. So that each cell outline was manually separated by drawing the lines along the visible contours of cell walls. Measurement of the impact damage dimensions was done by MIP software for the surface section (major and minor width, w1 and w2) and the depth section (depth, d and major width, w1). The results indicated the significant differences between water content, cell turgor pressure, cell area and cell perimeter over 16 weeks storage. Generally, by increasing impact intensity the water content, cell turgor pressure, cell area and cell perimeter significantly decreased. Also interaction effect of storage time, impact level and radius of curvature for impact damage of potato tissue was significant.

Conclusion
The cell turgor pressure at the impact location on the potato tubers had the similar trend with the water content. SEM investigation showed that potato parenchyma, which was high preserved by HMDS drying, had consisted of the pentagon and hexagonal thin-wall cells with the average cell area of 23.14 × 103 ± 0.178 μm2, the average cell perimeter of 564.98 ± 2.008 μm at week 0. The higher impact damage was at week 16 of storage, impact level 2 and the radius of curvature of 35 mm compared to the other treatment.

Biological and Biosystems Engineering

Review of some of Coating Seed Factors in Rotary Pan Coater

Volume 8, Issue 1, 2018, Pages 31-41

https://doi.org/10.22067/jam.v8i1.58334

F. Ranjbar, M. H. Kianmehr

Abstract Introduction
Today, hybrid seeds are expensive because the company that produces them spends a lot of money on research and development that often takes years to accomplish. So precise planting of seeds in order to create the best growing condition for all seeds is important. Modified size and shape of seeds for precision planting, providing macro and micro nutrients since the start of seed germination and control pests and diseases are goals that are possible by coating seeds. The overall process of seed coating or seed pelleting comprises a number of important stages: 1- Droplet formation 2- Droplet travel 3- Impingement 4- Wetting 5- Spreading 6- Coalescence. Seed coating was largely borrowed from the confectionery industry which had developed this technique over the ages and is still widely used today. The seed industry concentrated on using the rotary drum or pan. This type of pan or drum was used for batches of up to 150–200 kg. Some rotary drum coater were developed subsequently which improved handling, particularly in the way the drying air was introduced and extracted. The pan of drum rotary coater is placed at the end of a tilted rotating shaft that is turned at a constant speed about 15- 20 rpm. Then a nozzle is spraying proper amount of coating solution on the seeds. The aim of this study was to evaluate technology and determine the factors affecting its quality coverage.

Materials and Methods
This experiment lay out in factorial experiment based on random complete block design with three replications. The first factor was vertically distance nozzle from seed bed in two levels 150 and 300 mm, second factor was the nozzle installed location in two levels installed in 1/4 diameter upper center and in center of cylinder, and third factor was concentration of binder polyvinylpyrrolidone (PVP) in three levels 50, 75 and 100 g kg-1 kaolin. In order to measure the pellet error percent, first 100 pellets were selected and broken. No seed or multi-seed pellets were counted. For measuring physical strength of pellets, instron machine were implemented in physical properties laboratory in Aborihan department of Tehran University. Its load cell capacity was 490 N. Forward speed of the instron was 5 mm per minute. Germination test were performed in the laboratory in dryland agricultural substitute Sararood, Kermanshah.

Results and Discussion
The results showed that the nozzle distance from the seed bed had a significant effect on all measured traits (1% level). With increasing distance from the seed bed, the physical strength of pellet and the percentage of pellet error decreased but germination increased. In fact, with increasing nozzle distance from 150 mm to 300 mm, the physical strength of pellet decreased from 22.8 N to 21.4 N, the pellet error decreased from 4.1% to 2.1% but germination increased from 71.3 to 73.4 percent. The used binder quantity had a significant effect on all measured traits (1% level). By increasing of using binder, the physical strength of pellet and the percentage of pellet error increased but germination strongly decreased. In the other word, with increasing used binder from 50g to 100g per one kilogram kaolin, the physical strength of pellet increased from 13.9N to 29.1N, the pellet error increased from.2.01 to 4.18 percent but germination decreased from 90.42 to 53.17 percent. The nozzle installed location had a significant effect only on the pellet error (1% level). In the other word, the nozzle installed on the cylindrical center is better than nozzle installed in 1/4 diameter upper center. There was negative significant correlation (r=-0.96) between physical strength shell characteristics and germination. So increasing the physical strength of the shell is reduced germination. There was a significant correlation (r= 0.621) between physical strength and pellet error percentage. So with increasing physical shell strength, pellet error was increased.

Biological and Biosystems Engineering

Effect of nanoclay particles on some physical and mechanical properties of soils

Volume 6, Issue 1, 2016, Pages 250-258

https://doi.org/10.22067/jam.v6i1.28397

H. Sharifnasab, N. Abbasi

Abstract Introduction: As a mechanical tillage practices on soil preparation improve soil structure, increase in porosity, better distribution of soil aggregates and eventually modify the physical properties of soil. The use of nano-technology in agricultural science and its application in tillage for improving the physical properties and mechanical issues has grown substantially.
Nanotechnology is an appropriate way to reduce soil limitations. However the nanoparticles are very small amounts in soil, due to features such as high surface area, surface charge (appearance) and sometimes porous nano-engineering of physical-chemical properties of soil are affected significantly (Mohammadi & Niazian, 2013). To use of nanomaterials in the territory of a new issue (Taipodia et al., 2011). Small developments on the use of nanoparticles to improve soil quality and land reform have been taken (Theron et al., 2008).
Clay soil was used to enhance the compressive strength (Yonekura & Miwa, 1993). Nanosilica particle effects were examined for increasing resistance against penetration and consolidation (Noll et al., 1992). In 2005, these particles were used to increase adhesion and reduce viscosity. It seemed that the adhesion of the particles was depended on Nanosilica (Mohammadi & Niazian, 2013). The use of nanomaterials showed that the increased pH and soil fertility, improved soil physical structure, and reduced mobility, availability and toxicity of heavy metals and other environmental factors and those that will stabilize the soil components and subsides the erosion in the mining pick, (Lal, 2008). In agriculture, the soil conditioner studies have shown that nanoparticles can mine the soil quality by increasing water-holding capacity, increasing silt and clay and improve levels of nutrients, and eliminate toxins, (Liu and Lal, 2012).In this study, the effect on some physical and mechanical properties of soil contain clay gradation, Atterberg limits, specifications compression and shear parameters of soil were investigated.
Materials and Methods: The study was done for 2 years at the Research Institute of Agricultural Engineering Soil Dynamics Laboratory in a completely randomized design with three replications.
Soil samples were used for different soil textures. Three types of soil texture, light, medium and heavy were considered. Nanoclay has a mineral base and can improve the properties of the soil. Two levels of the nanoclay containing zero and one percent of the nanoclay, 3 to 6 treatments in different physical and mechanical tests were repeated.
The test specimens were prepared in triplicate test and physical, mechanical and chemical testing was performed according to ASTM standard on all models. Mesh test samples were performed by sieve and hydrometer methods according to standard ASTM-D422-98.
Plastic soil properties were expressed by the Atterberg Limits, measure the ability to absorb water, soil and to a fine particle adhesion amount and type of fine particles in the soil. Psychological testing was performed to determine the extent and the paste according to ASTM-D4318-98 standard.
The maximum dry density and optimum moisture content of the soil compaction characteristics are the most important soil properties such as soil density development projects are in operation. In agricultural applications, in particular for tillage, these two factors are of particular importance. In this study, Praktor standard density testing was performed on the different treatments.
In this research, not consolidate Undrained (UU) testing methods were used. The stress tests were done at three levels 100, 200 and 300 kPa respectively.
Results and Discussion: Adding nanoparticles of clay significant impact on the size of the samples did not curve. As well as to determine the impact of nano-clay soil Plastic characteristics as psychological tests and the paste was treated on the results of these tests for different treatments and repeated ANOVA revealed a significant effect of soil type on soil Plastic characteristics. The type of control or significant influence characteristics Plastic application of nano regard.
The optimum moisture content and maximum dry density values of each sample was extracted from the respective curves that their results suggest that addition of nanoclay had a considerable impact on the density profile.
It was observed that the use of nanoparticles in soil reduced the average amount of cohesion and internal friction angle was large. This means that the increasing the nanoclay reduces the shear parameters and therefore the shear strength of the soil. This is very important in terms of tillage. Reducing the adhesion of soil particles allows the lumps are crushed with less energy.
Conclusions: Based on the results of studies and experiments conducted in this study, the following conclusions can be extracted.
- Adding nanoparticles of clay soils affect the grading curve display.
- The effect of nanoclay had more psychological impact than the same amount in the dough.
- The results showed that the addition of nanoclay had a considerable impact on the density profile.
- The use of nanoparticles in soil reduced the average amount of cohesion and internal friction angle is large.
- Due to the increase of nano-clay soil, shear strength decreased as a result of the shear parameters.

Biological and Biosystems Engineering

Modeling moisture absorption kinetics of barley grain using viscoelastic model and neural networks

Volume 5, Issue 2, 2015, Pages 270-280

https://doi.org/10.22067/jam.v5i2.28305

M. Kamali, S. J. Razavi, M. Sadeghi, S. M. Shafaei

Abstract Introduction: Barley is one of the most important grains with high digestible starch making it a main source of energy in human nutrition as well as in livestock rations formulation and feeding. Starch is the main part of barley grain and it has an inverse relation with its protein. It has a digestible foodstuff of 80 to 84 percent of its dry matter content. Barley as livestock foodstuff should be processed and it is done in several ways. A customary method for processing barley in dairy farms is its size reduction by milling (Hunt, 1996). An alternative method of barley processing is steam rolling. However, because of the high cost of steam generators a method of soaking with heating has been considered as an alternative method for steam rolling (Yang et al., 2000). The rate of moisture absorption by grains during the soaking process varies considerably and depends on the size of the grain, water temperature and the length of soaking. High temperature water soaking is an ordinary way to reduce the time duration for reaching a high rate of moisture absorption during the soaking process (Kashaninejad et al., 2009). Various studies have shown that these models have adequate accuracy in analyzing drying and moisture absorption processes for most agricultural products (Abu-Ghannam and McKenna, 1997). Some researchers have modeled beans moisture absorption behavior using 14 mathematical models and found that the Weibull model had the most conformity with variations in experimental data (Shafaei and Masoumi, 2014c). Observations made by researchers indicate that the moisture absorption process in various materials encompasses a primary phase with a fast rate and a second phase with a lower rate. The second phase in moisture absorption is called the relaxation phase. The main problem with all the mathematical and experimental models is the lack of the model’s ability to evaluate the rate of moisture absorption in the secondary phase. Artificial Neural Network (ANN) as an important artificial intelligent method comparable to human brain capabilities is applied to train and store data in the form of weighted networks (Dayhoff, 1990). This method has superiority to many ordinary statistical and model making methods. In comparison to linear regression models, ANN does not require placing estimated values around mean values and for this reason it retains actual variations in the data being analyzed. Prediction by using trained ANN enables the researchers to decrease or increase input and output variables.Therefore, it is possible to produce a multivariate model with an output even more than the objectives deemed necessary (Heristev, 1998). The goal of this research was to predict instant moisture content of three barley varieties (Reyhan3, Fajr and MB862) during the soaking process under three temperature levels (10, 20 and 45 ◦C) using two conventional ANN methods of multilayer perceptron (MLP) and radial basis function (RBF) in comparison with viscoelastic mathematical model and reporting the results.
Materials and method: Barley varieties were collected from the Isfahan Province Agriculture Organization grain depository and were cleaned and the debris were separated before the experiments. The selected grains were sorted to three groups of small, medium and large grains sizes. To exclude the effect of grain size during moisture absorption, the medium size grains were used. The moisture content of the grains was determined based on the ASAE S352.2 DEC97 (ASAE, 1999) which were %8.23, %8.62 and %8.89 on a dry basis for Reyhan3, Fajr and MB862, respectively with no significant difference at %5 probability level (p>0.05). Experiments were conducted under three temperatures (10, 20 and 45 ◦C) in the refrigerator, at room temperature and in the oven, respectively for each variety. In each experiment, 10 medium size grains were selected randomly and weighed with an AND laboratory scale model Gf-400 (made in Japan) and placed in foam containers having 200 mg of distilled water. Grains were weighed after a predetermined period of elapsed time (5, 10, 15, 30, 60, 120, etc. minutes). The experiments were conducted with three replications and moisture absorption rates were determined by the equations presented by McWatters et al., 2002. The experiments were conducted on a time table based on which the time for the dissolving of grains was reached. In this case, the moisture content of the grains reaches the saturation point. According to equations presented by Peleg, as water density increases as much as 0.01 gram due to grains dissolving in water, the saturation point has been reached (Peleg, 1988). For this reason, distilled water density was measured and controlled before and after each experiment by a pycnometer. Neural network was designed according to the two methods of multi-layer perceptron (MLP) and radial basis function (RBF) with three neuron layers. The first layer, i.e. input layer, is independent variables of temperature and time.The second layer, i.e. hidden layers, is the networks hidden layer and the third layer, i.e. output layer, is the dependent variable of moisture content which was selected. In each case, the nonlinear reduced gradient, combined gradient and BFGS algorithm, and Trigonometric, Logarithmic, Gaussian, and Logical functions were used to train, test and evaluate the network. To evaluate the predicting viscoelastic model and the network, we used statistical indices maximum value of coefficient of determination (R2) and minimum value of mean square error (RMSE).
Results and Discussion: Moisture absorption curves showed that as the temperature increases, moisture absorption rate increases as well. Higher equilibrium moisture levels are obtained in water with higher temperatures. This phenomenon is the result of increased moisture diffusion in grains due to higher temperature levels. Higher water temperatures causes grain internal material which is mainly starch to gelatinize and, thus, the internal tissues resistance to moisture absorption reduces (Ranjbari et al., 2011). The moisture absorption rate increases as immersion temperature and gelatinization temperature reach closer to each other.
Conclusions: The results of this study showed that although viscoelastic mathematical model has an adequate accuracy for instant prediction of barley grain moisture content, it has a lower accuracy compared to intelligent models. On the other hand, among the two neural network methods, MLP method has a higher accuracy in predicting moisture content compared to RBF method. MLP obtained the best results for three varieties of barley because of back- propagation learning algorithm with BFGS algorithm and 2-4-1 network structure. According to the prediction of the best neural network which was selected, three-dimensional graphs of moisture content based on temperature and time variables, showed that with an increase in temperature and duration of immersion, moisture absorption increases for three varieties of barley.

Biological and Biosystems Engineering

Effect of Potassium Permanganate Nano-Zeolite and Storage Time on Physicochemical Properties of Kiwifruit (Hayward)

Volume 4, Issue 1, 2014, Pages 37-49

https://doi.org/10.22067/jam.v4i1.33163

H. Mirzaee Moghaddam, M. H. Khoshtaghaza, M. Barzegar Bafroee, A. Salimi

Abstract In this research, kiwifruits (Hayward) were selected in two mass ranges (large and small). They were placed in one-liter glass bottles in the vicinity of the polyethylene sachets containing potassium permanganate nano-zeolite (0, 0.2, 0.4 and 0.8 g) and were stored in a germinator (5°C temperature and 30% relative humidity). Then, the physicochemical properties of the fruits (soluble solid content, pH, moisture content and fruit firmness) and potassium permanganate nano-zeolite color (L, Hue angle, Chroma and E) were measured after t 0, 2, 4 and 6 weeks of storage. The factorial treatment structure based on completely randomized block design was used for analyzing the obtained data. The results of analysis showed that potassium permanganate nano-zeolite had a significant effect on the measured physicochemical properties, except for the moisture content (P

Biological and Biosystems Engineering

Design, Implementation and Evaluation of a Torque Transducer with Ability of Real-time Torque Monitoring

Volume 4, Issue 1, 2014, Pages 73-78

https://doi.org/10.22067/jam.v4i1.33167

A. Zeinali, A. Farzad, M. H. Aghkhani

Abstract Torque, speed, and power as mechanical variables are associated with the functional performance of any rotating machinery. The real-time performance and the efficiency of a machine can be determined with on-line measurement of these parameters. In this investigation a rotary torque meter (transducer) was constructed from strain gauge sensors for measuring the torque of rotating shafts. The system converts the torque of rotating shaft into voltage signals, based on the principle of strain gauge resistance. The signals are then amplified and converted into digital signals. These digital signals are sent to a RF receiver circuit for displaying and storage. Results of static calibration and a series of dynamic tests confirmed a satisfactory operation of the designed apparatus in various conditions. Also, the torque measuring range, resolution and the accuracy were from 3 to 700 N m, 3 N m and 1%, respectively.