Design, Construction and Evaluation of a Silage Corn Chopper Equipped with Electromotor Power Unit

Document Type : Short Paper

Authors

• R. Hadipour Rokni ¹
• A. Rezaei Asl ¹
• R. Tabatabaei koloor ²

¹ Gorgan Agricultural Sciences and Natural Resources University, Gorgan, Iran

² Sari Agricultural Sciences and Natural Resources University, Sari, Iran

https://doi.org/10.22067/jam.v8i2.64433

Abstract

Introduction
In most small and medium-size traditional animal farms, silage corn is chopped manually. In order to prepare appropriate chopper for small animal production firms, a small electrical powered chopper was designed and developed.

Materials and Methods
The machine consisted of different parts, including chassis, driveline, power transmission, feeding and cutting unit. To provide the power for cutting cylinder and feeding rollers, 3.7 kW and 1.5 kW electro-motors were selected and used, respectively. Power was transferred from electro-motors to the cutting cylinder and feeding rollers by pulley and belts. Feeding entrance area was 62.5 cm²with theoretical capacity of 1.13 kgs^-1 and feeding unit power consumption of 0.97 kW. The main parts of feeding and cutting units were analyzed by ANSYS Software. Silage corn was provided at harvest time from the Dashte-Naz, Sari province, and transported to laboratory, immediately. The effect of cutting blades speed (400, 550 and 700 RPM) and feed rollers speed (350, 400 and 450 RPM) on the chopper performance (cutting and feeding energy consumption, chopped corn length and machine capacity) were investigated. The results then analyzed using completely randomized design in triplicates.

Results and Discussion
Analysis of variance showed that the speed of cutting blades, speed of feeding rollers and their interactions had significant effect on the energy consumption of cutting blades and machine capacity. The effect of speed of feeding rollers was significant on the energy consumption of feeding rollers at 1% level of significance. Also, The effect of speed of chopping blades, speed of feeding rollers and their interactions were significant on the length of chopped corn. Machine capacity increased by increasing in speed of chopping blades from 400 to 550 RPM and decreased by increasing from 550 to 700 RPM. Increasing in the speed of the blades at the moment of impact, caused to effectively cut the stem fibers before being compressed or bent. Increasing the speed beyond 550 RPM provided insufficient time for stem movement toward the blades and therefore, machine capacity decreased. By increasing the speed of feeding rollers, the consumed energy by cutting blades decreased and the energy consumption of feeding rollers, the length of chopped corn and the machine capacity increased. Since the machine capacity is depending on time, increasing in feeding rollers speed, decreased the time for chopping the feed stems resulted decreasing in machine capacity. Also, results depicted that the interaction between speed of cutting blades and feeding rollers had meaningful effect on the consumed energy by cutting blades. The maximum energy consumption was at the blade speed of 700 RPM and the feeding rollers speed of 350 RPM, and the minimum energy consumption was at the blade speed of 400 RPM and feeding rollers speed of 450 RPM. The maximum and minimum length of chopped corns was obtained at the blade speed of 400 RPM and 700 RPM, respectively and correspondingly at the rollers speed of 450 RPM and 350 RPM, respectively. The maximum capacity of the machine was obtained at the blade speed of 550 RPM and rollers speed of 450 RPM.

Conclusion
Since the length of the chopped corn for animal feeding is 20-30 mm, the optimum speed of cutting blades, minimum energy consumption and maximum machine capacity was obtained as 550 RPM and the optimum speed of feeding rollers was at 400 RPM. For feeding high yielding dairy cows, goats and sheeps that need smaller sized forage, it recommended that feeding rollers speed to be adjusted at 350 RPM. At the same speed, the mean length of chopped corn was 8-19 mm.

Keywords

• Chopper
• Cutting blade
• Silage corn

20.1001.1.22286829.1397.8.2.18.2

Main Subjects

• Design and Construction

References

1. Adapa, P., L. Tabil, and G. Schoenau. 2011. Grinding performance and physical properties of non-treated and steam exploded barley, canola, oat and wheat straw. Biomass and Bioenergy 35: 549-561.

2. Azadbakht, M., A. R. Asl, and K. T. Zahedi. 2014. Energy requirement for cutting corn stalks (Single Cross 704 Var.). World Academy of Science, Engineering and Technology, International Journal of Biological, Biomolecular, Agricultural, Food and Biotechnological Engineering 8: 479-482.

3. Behrozi-lar, M. 1999. Engineering parinciples of Agricultural Machines. Islamic Azad University of Tehran. (In Farsi).

4. Bitra, V. S., A. R. Womac, C. Igathinathane, P. I. Miu, Y. T. Yang, D. R. Smith, N. Chevanan, and S. Sokhansanj. 2009. Direct measures of mechanical energy for knife mill size reduction of switchgrass, wheat straw, and corn stover. Bioresource Technology 100: 6578-6585.

5. Chen, Y., J. L. Gratton, and J. Liu. 2004. Power requirements of hemp cutting and conditioning. Biosystems Engineering 87: 417-424.

6. Halyk, R., and L. Hurlbut. 1968. Tensile and shear strength characteristics of alfalfa stems. Transactions of the ASAE 11: 256-0257.

7. Igathinathane, C., A. Womac, and S. Sokhansanj. 2010. Corn stalk orientation effect on mechanical cutting. Biosystems Engineering 107: 97-106.

8. Ince, A., S. Uğurluay, E. Güzel, and M. Özcan. 2005. Bending and shearing characteristics of sunflower stalk residue. Biosystems Engineering 92: 175-181.

9. Krone, B., and R. Heinz. 2002. Harvesting maching, especially a self-propelled pick-up chopper. United States Patent. Noumber: US 2002/0029552 A1.Mar.14.

10. McRandal, D., and P. McNulty. 1980. Mechanical and physical properties of grasses. Transactions of the ASAE 23: 816-821.

11. Shadravan, I. 2007. Mechanical Engineering Design. Tehran University Publisher.

12. Tabatabaei, K., and R. R. Hadipoor. 2016. Effect of blade parameters and some physical propertis sillage corn stem of the cutting force, cutting strerm and cutting Special energy. in Final Research Report. Sari Agricultural Sciences and Natural Resources University, Sari, Iran.

13. Tamaskani Zahedi, K. 2014. Design, Development and evaluation of crushing machine for corn.M.Sc. Thesis. Faculty of Agriculture, Gorgan Agricultural Sciences and Natural Resources, Iran.

14. Womac, A., M. Yu, C. Igathinathane, P. Ye, D. Hayes, S. Narayan, S. Sokhansanj, and L. Wright. 2005. Shearing characteristics of biomass for size reduction. ASAE Paper 56058.