Evaluating the Effect of Soil Deformation Rate on the Estimation of the Energy Consumption in Soil-Tire Interactions Using the Pressure-Sinkage Equation

Articles in Press

Document Type : Research Article-en

Authors

• H. Asadollahi ¹
• B. Mohammadi-Alasti ²
• A. Mardani ³
• M Abbasgholipour ¹

¹ Department of Mechanical Engineering of Biosystems, Bonab Branch, Islamic Azad University, Bonab, Iran

² Associate Professor, Department of Mechanical Engineering of Biosystems, Bonab Branch, Islamic Azad University, Bonab, Iran.

³ Associate Professor, Department of Mechanical Engineering of Biosystems, Faculty of Agriculture, Urmia University, Urmia, Iran

https://doi.org/10.22067/jam.2024.89154.1269

Abstract

Understanding soil deformation dynamics is critical in various fields, such as off-road vehicle mobility, agriculture, and soil mechanics. In particular, evaluating soil-tire interactions is essential for optimizing energy consumption and minimizing the negative effects of soil compaction. This study investigates the effect of soil deformation rates on the pressure-sinkage relationship and energy consumption using a controlled soil bin environment and a bevameter system. The primary objective of the study is to examine how different traffic levels and varying penetration rates influence the energy required to achieve specific sinkage depths. The study employed a completely randomized block design, with each treatment replicated three times to ensure precision and reliability. Quantitative measurements were obtained using a load cell attached to a bevameter, capturing the forces at a sampling frequency of 30 Hz. Results demonstrated a significant influence of both traffic level and penetration velocity on soil resistance and energy consumption. For the larger plate, the pressure required for penetration increased with higher velocities and traffic levels. At the highest velocity (45 mm s^-1) and with 8 passes, the pressure needed for sinkage was maximal. The energy consumption for each scenario was calculated by integrating the area under the force-sinkage curve. The analysis of variance (ANOVA) revealed that the number of wheel passes, plate size, and penetration velocity significantly affected energy consumption. For instance, at the highest sinkage depth (60 mm), the energy consumption for the larger plate at 45 mm/s and with 8 passes was nearly double that of the smaller plate. These results emphasize the importance of considering both traffic-induced compaction and velocity when designing off-road vehicles or agricultural machinery that interact with deformable terrains.

Keywords

• Bevameter
• Penetration rate
• Soil deformation energy
• Terramechanics
• Multiple passes

Main Subjects

• The relationship between machine and soil

©2025 The author(s). This is an open access article distributed under Creative Commons Attribution 4.0 International License (CC BY 4.0)

References

1. Apfelbeck, M., Kuß, S., Rebele, B., & Schäfer, B. (2011). A systematic approach to reliably characterize soils based on Bevameter testing. Journal of Terramechanics, 48(5), 360-371. https://doi.org/10.1016/j.jterra.2011.04.001
2. (2018). ANSI/ASAE S296.5, DEC2003 (R2018), General Terminology for Traction of Agricultural Traction and Transport Devices and Vehicles. ASAE, St. Joseph, MI.
3. Bekker, M. G. (1960). Off-the-Road Locomotion University of Michigan Press. Ann Arbor, 27-29.
4. Bekker, M. G. (1969). Off-Road Locomotion. Ordnance, 53(292), 416-418. https://www.jstor.org/stable/45361962
5. Brunskill, C., Patel, N., Gouache, T. P., Scott, G. P., Saaj, C. M., Matthews, M., & Cui, L. (2011). Characterisation of martian soil simulants for the ExoMars rover testbed. Journal of Terramechanics, 48(6), 419-438.
6. Earl, R., & Alexandrou, A. (2001). Deformation processes below a plate sinkage test on sandy loam soil: experimental approach. Journal of Terramechanics, 38(3), 153-162.
7. Golanbari, B., & Mardani, A. (2023). Analytical Traction Force Model Development for Soil-Tire Interaction: Incorporating Dynamic Contact Area and Parameter Analysis Using Taguchi Method. Biomechanism and Bioenergy Research, 2(2), 56-64.
8. Golanbari, B., & Mardani, A. (2024). An analytical model for stress estimation at the soil-tire interface using the dynamic contact length. Journal of Terramechanics, 111, 1-7. https://doi.org/10.1016/j.jterra.2023.08.006
9. Golanbari, B., Mardani, A., Hosainpour, A., & Taghavifar, H. (2023). Modeling Soil Deformation for Off-Road Vehicles Using Deep Learning Optimized by Grey Wolf Algorithm. Journal of Agricultural Machinery, 14(1), 69-82. https://doi.org/10.22067/jam.2023.84339.1188
10. Gonzalez, R., & Iagnemma, K. (2018). Slippage estimation and compensation for planetary exploration rovers. State of the art and future challenges. Journal of Field Robotics, 35(4), 564-577.
11. Grahn, M. (1996). Einfluß der Fahrgeschwindigkeit auf die Einsinkung und den Rollwiderstand von Radfahrzeugen auf Geländeböden.
12. Kruger, R., Els, P. S., & Hamersma, H. A. (2023). Experimental investigation of factors affecting the characterisation of soil strength properties using a Bevameter in-situ plate sinkage and shear test apparatus. Journal of Terramechanics, 109, 45-62. https://doi.org/10.1016/j.jterra.2023.06.002
13. Majdoubi, R., Masmoudi, L., & Elharif, A. (2024). Analysis of soil compaction under different wheel applications using a dynamical cone penetrometer. Journal of Terramechanics, 111, 21-30. https://doi.org/10.1016/j.jterra.2023.09.001
14. Mardani, A., & Golanbari, B. (2024). Indoor measurement and analysis on soil-traction device interaction using a soil bin. Scientific Reports, 14(1), 10077.
15. Taghavifar, H., & Mardani, A. (2013). Investigating the effect of velocity, inflation pressure, and vertical load on rolling resistance of a radial ply tire. Journal of Terramechanics, 50(2), 99-106.
16. Taghavifar, H., & Mardani, A. (2014). Analyses of energy dissipation of run-off-road wheeled vehicles utilizing controlled soil bin facility environment. Energy, 66, 973-980.
17. Taheri, A., & Tatsuoka, F. (2015). Small-and large-strain behaviour of a cement-treated soil during various loading histories and testing conditions. Acta Geotechnica, 10(1), 131-155.