Bioenergy
A. Waismoradi; M. E. Khorasani; H. Bahrami; S. M. Safieddin Ardebili; H. Zaki Dizaji
Abstract
IntroductionToday, the number of diesel engines is increasing due to their high efficiency and low greenhouse gases. In the present study, the effect of adding nano cellulose as nanoparticles to diesel fuel on the performance parameters and emissions of diesel engine was investigated. Nano cellulose ...
Read More
IntroductionToday, the number of diesel engines is increasing due to their high efficiency and low greenhouse gases. In the present study, the effect of adding nano cellulose as nanoparticles to diesel fuel on the performance parameters and emissions of diesel engine was investigated. Nano cellulose was provided by the Nano Novin Company in Sari. Nano cellulose values were considered at 3 levels of zero, 25 ppm and 75 ppm. Also, the tests were performed at 3 engine speed of 1600, 2000 and 2400 rpm in full load mode.Materials and MethodsIn this study, nanocellulose was used as nanoparticles to add to diesel and to evaluate the performance and emission parameters of the engine. To prevent the deposition of nano cellulose in diesel fuel, jelly type nano cellulose was used. The samples were named after adding different amounts of nano cellulose, abbreviated D100N0, D100N25 and D100N75. D100 means 100% pure diesel and N means different amounts of nano cellulose with different amounts. Ultrasound was used to obtain homogeneous samples. About 3 liters were prepared from each sample so that it could be used for at least 3 repetitions. The required tests were performed at three different speeds of 1600, 2000 and 2400 rpm in full load mode. The necessary equipment was used to measure the performance parameters and air emissions, including diesel engine connected to the dynamometer, emissions measuring device, fuel system and control room (to apply the load and provide conditions for each treatment and data collection). The air-cooled, four-stroke, compression-ignition single-cylinder engine made by the Italian company Lombardini was used. The D400 eddy current dynamometer made in Germany was used. The ability to measure power by this dynamometer is a maximum of 21 hp, a maximum speed of 10,000 rpm and a maximum torque of 80 N.m. To measure of emissions, the MAHA MGT5 emissions meter was used. This device is able to measure the values of CO, CO2, NOX, O2 and UHC.Results and DiscussionThe results showed that increasing engine speed in all fuel combinations increased engine power, specific fuel consumption, carbon monoxide and unburned hydrocarbons and decreased torque. Also, increasing the amount of nano cellulose per engine speed increased the amount of power and torque, but reduced the specific fuel consumption, carbon monoxide and unburned hydrocarbons. The amount of NOX increased with increasing engine speed, but at each engine speed the addition of 25 ppm nanocellulose to pure diesel significantly increased the amount of NOX. But at low speed, increasing 75 ppm nanocellulose to pure diesel reduced the amount of NOX.ConclusionThe results of this study showed that the addition of nano cellulose as nanoparticles can improve the performance of diesel engines and also reduce the amount of emissions gases emitted from the engine. The results also showed that increasing 25ppm nanocellulose had a greater effect on engine performance. But to reduce the amount of emissions, 75 ppm nanocellulose was better.
S. Ahmadipour; M. H. Aghkhani; J. Zareei
Abstract
Introduction Today, maximizing the efficiency of fuels and increasing the output power of diesel engines is considered inevitable due to the increasing need for energy resources, the reduction of fossil fuel resources, the need to maintain the environment, reduce air pollution, and limit the electricity ...
Read More
Introduction Today, maximizing the efficiency of fuels and increasing the output power of diesel engines is considered inevitable due to the increasing need for energy resources, the reduction of fossil fuel resources, the need to maintain the environment, reduce air pollution, and limit the electricity supply and fuel supply. In the large cities of Iran, the problem of vehicle pollution is one of the main problems. The lack of proper fuel, soot filters, and absence of requirement for a technical inspection of diesel vehicles have led to an increase in mortality and the growth of lung cancer due to pollution. All of studies indicate that fossil fuels, despite the low cost of production, will increase the cost of both living and environment. A solution for this crisis is to reduce the sources of pollutant-producing sources from the source of these pollutants. In the internal combustion engines, the compression ratio and alternative fuels are two important factors affecting engine performance and exhaust emission. Materials and Methods In this research, a one-dimensional computational fluid dynamics solution with GT-Power software was used to simulate a six-cylinder diesel engine to study the performance and exhaust emissions with different compression ratios and alternative fuels. The compression ratio was chosen to be 15:1 to 19:1 with an interval at unity. Alternative fuels such as (as base diesel), methanol, ethanol, diesel and ethanol, biodiesel and decane were selected. To modeling engine, first, all parts of the engine were introduced as a real six-cylinder engine, and then the required data were entered according to the actual engine conditions at the atmospheric pressure of one atmosphere. Before this investigation was carried out, a validation model for evaluation was done by experimental and simulation data. The validation results showed that software model error is acceptable and the model has a good capability of fitting and predicting. Results and Discussion The engine performance was evaluated in terms of engine power, engine torque, and specific fuel consumption at different engine compression ratio and fuel. The results showed that with increasing the compression ratio, brake power and brake torque increased. Among the fuels used in this engine, the maximum brake power and brake torque in the compression ratio of 19 with the decane fuel were 3.86% higher than that the base fuel and the lowest value was awarded in the compression ratio of 15, with methanol fuel and it was equal with 56.04%. The results indicated that by increasing compression ratio, the brake specific fuel consumption was reduced due to more power than the fuel consumed in the engine. A fuel with lower heating value should be injected more mass to the engine. This will increase the brake specific fuel consumption. In this research, the decane fuel with a compression ratio of 19 with a reduction of 3.72% had the lowest brake specific fuel consumption among other fuels. The CO emission from the engine largely depended on the fuel's properties, the availability of oxygen, the fuel mix with air, temperature, and turbulence inside the combustion chamber. The results highlighted that by increasing compression ratio, CO emission increased and CO emission in biodiesel fuel, with a compression ratio of 15, was decreased by 82.37% compared to the base. CO2 emissions are not too harmful to humans, but they increase the potential for ozone depletion and global warming. With increasing compression ratio, CO2 and HC emissions increased for all fuels, CO2 emissions have risen up the base. The fuel heating mechanism, combustion temperature, oxygen content, and gas fuel availability are the most important factors in the formation of NOx. With increasing the compression ratio, the amount of NOX increases, which is due to the high temperature in the cylinder at a higher compression ratio. The viscosity and density of fuels have an effect on NOX emission, and because of the larger droplets of the fuel, it released NOX. The highest NOx emissions from biodiesel fuel are due to the high oxygen content of this fuel and the lowest NOx emissions from decane fuel, due to the low density of the fuel compared to other fuels. Conclusion The results of this study showed that the decane fuel with a compression ratio of 19 in total had the best functional and pollutant characteristics among the six fuel used in this study. Therefore, this fuel can be the best alternative for diesel fuel.
S. Abbasi; H. Bahrami; B. Ghobadian; M. Kiani Deh Kiani
Abstract
Introduction The extensive use of diesel engines in agricultural activities and transportation, led to the emergence of serious challenges in providing and evaluating alternative fuels from different sources in addition to the chemical properties close to diesel fuel, including properties such as renewable, ...
Read More
Introduction The extensive use of diesel engines in agricultural activities and transportation, led to the emergence of serious challenges in providing and evaluating alternative fuels from different sources in addition to the chemical properties close to diesel fuel, including properties such as renewable, inexpensive and have fewer emissions. Biodiesel is one of the alternative fuels. Many studies have been carried out on the use of biodiesel in pure form or blended with diesel fuel about combustion, performance and emission parameters of engines. One of the parameters that have been less discussed is energy balance. In providing alternative fuels, biodiesel from waste cooking oil due to its low cost compared with biodiesel from plant oils, is the promising option. The properties of biodiesel and diesel fuels, in general, show many similarities, and therefore, biodiesel is rated as a realistic fuel as an alternative to diesel. The conversion of waste cooking oil into methyl esters through the transesterification process approximately reduces the molecular weight to one-third, reduces the viscosity by about one-seventh, reduces the flash point slightly and increases the volatility marginally, and reduces pour point considerably (Demirbas, 2009). In this study, effect of different percentages of biodiesel from waste cooking oil were investigated. Energy distribution study identify the energy losses ways in order to find the reduction solutions of them. Materials and Methods Renewable fuel used in this study consists of biodiesel produced from waste cooking oil by transesterification process (Table 1). Five diesel-biodiesel fuel blends with values of 0, 12, 22, 32 and 42 percent of biodiesel that are signs for B0, B12, B22, B32 and B42, respectively. The test engine was a diesel engine, single-cylinder, four-stroke, compression ignition and aircooled, series 3LD510 in the laboratory of renewable energies of agricultural faculty, Tarbiat Modarres University. The engine is connected to a dynamometer and after reaching steady state conditions data were obtained (Fig. 1). In thermal balance study, combustion process merely as a process intended to free up energy fuel and the first law of thermodynamics is used (Koochak et al., 2000). The energy contained in fuel converted to useful and losses energies by combustion. Useful energy measured by dynamometer as brake power and losses energy including exhaust emission, cooling system losses and uncontrollable energy losses. Variance analysis of all engine energy balance done by split plot design based on a completely randomized design and the means were compared with each other using Duncan test at 5% probability. Results and Discussion Results showed that, in general, biodiesel use has a significant impact on all components of energy balance. Of total energy from fuel combustion, the share of energy losses to form of exhaust emissions the maximum value in all percentages allocated to biodiesel (Average 51.715 percent) with the maximum and minimum amount of B42 (55.982 percent) and B0 (46.481 percent), respectively (Fig. 2). Also, fuel blend with 12% biodiesel was diagnosed the best blend because of having the most useful power, having the lowest energy losses through the exhaust and cooling system. Conclusion Using biodiesel produced from waste cooking oil by transesterification process, lead to increase the useful power. The addition of biodiesel to pure diesel cause to significant reduction in the waste energy due to friction. In higher amounts of biodiesel increase energy losses especially through the exhaust and cooling system due to higher viscosity.
S. H. Hashemi Fard; M. Almassi; A. M. Borghaee; B. Beheshti
Abstract
The use of Bio-ethanol as an alternative diesel engine fuel is rapidly increasing. Bio-ethanol is mixed with diesel fuel at different ratios and used in CI and SI engines. Since vibrations have direct effects on users and engine components, for this reason analysis of vibration resulting from combustion ...
Read More
The use of Bio-ethanol as an alternative diesel engine fuel is rapidly increasing. Bio-ethanol is mixed with diesel fuel at different ratios and used in CI and SI engines. Since vibrations have direct effects on users and engine components, for this reason analysis of vibration resulting from combustion in CI engines is very important. In this study, evaluation of vibration was performed for both diesel and ethanol blends. Commercial diesel fuel (D100), E2 (2% ethanol and 98% diesel fuel), E5, E10, E15 and E20 were used in a two-wheel MITSUBISHI tractor. The engine was tested in 1200, 1600, 2000 and 2400 rpm for all fuel blends, and also the effect of load was investigated for D100 and E10. Results showed that vibration is significantly affected by fuel blend. It was observed that E10 had the lowest vibration while E20 had the highest value. It was also observed that vibration increased as engine speed increased for all fuel blends. It was found that both axial and lateral vibrations affected significantly by load. The lateral vibrations decreased continuously with load rise , but the axial vibrations increased initially but started to follow a reverse trend.
