with the collaboration of Iranian Society of Mechanical Engineers (ISME)

Document Type : Research Article

Authors

Department of Biosystems Engineering, College of Agriculture, Shiraz University, Shiraz, Iran

Abstract

Introduction
Tillage is one of the most important field operations to improve soil structure and physical conditions and provide the proper plant site. Conservation tillage is one of the methods of tillage that reduces tillage costs. The blade is one of the most important consumed components of tillage tools in the conservation tillage, which is very important for how it is adjusted and its effect on the quality of tillage and energy required of tillage tools. According to the research conducted on the importance of optimizing tillage implements, the aim of this study was oriented to determine the optimum rake angle of a narrow-modified winged and non-winged blade in the field soil.
Materials and Methods
The tests were conducted in the 22nd part of farms in Agriculture School (Bajgah zone) of Shiraz University. Three levels of blade rake angles (20, 25, and 30 degrees), two levels of tillage depth (15 and 20 cm), and two levels of forward speed (2 and 3 km h-1) were the treatments of this study. Draft, fuel consumption, slippage, soil disturbance area, soil upheaving area, and specific draft were the measured parameters and they were measured for each combination of the treatments. The RNAM test code was then used to measure the draft force. In order to  measure fuel consumption, two flow meters were used in the round way as a closed-loop. The encoder and the fifth wheel were also employed to measure the slippage. The profilometer and laser meter were applied to measure the soil upheaving and disturbance areas. The split-split plot on randomized complete block design was used to do the field experiments in three replication and the data analysis was performed by SAS software (9.4 edition). Multivariate linear regression was used to determine the optimum values of the mentioned parameters. For this purpose, the lowest value of draft, fuel consumption, specific draft, tractor driver wheel slip, and the highest soil disturbance and upheaving areas was considered.
Results and Discusion
The results showed that the magnitude of draft increased with rake angle, therefore, the minimum draft was obtained in the rake angle of 20°. As the blade rake angle increased, the amount of soil disturbance area was increased and the maximum soil disturbance was obtained in the rake angle of 30°. The mean slip values of the tractor driver wheels when using non-winged blade were not significant for three levels of blade rake angles and it was significant for two velocity levels. With increasing in rake angle from 20 to 25°, the mean values of specific draft were increased, but with changeing the rake angle from 25 to 30°, there was not significant difference between specific draft values. The difference between the magnitude of tractor driver wheels slip for three levels of rake angle was not significant. Increasing the rake angle had a significant effect on tractor fuel consomption, such that it increased by increasing the rake angle values.
Conclusion
The optimum rake angle for the non-winged blade mode was 20° with R2 of 0.73 and for the winged blade mode was 30° with R2 of 0.90. The optimum depth for the non-winged blade was 19.98 cm with R2 of 0.99 and for the winged blade was 20 cm with R2 of 0.97. Also, the optimum forward speed values for the non-winged blade was 2.21 km h-1 with R2 of 0.43 and for the winged blade was 2.03 km h-1 with R2 of 0.84.

Keywords

Open Access

©2020 The author(s). This article is licensed under Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source.

1. Abbaspour-Fard, M. H., S. A. Hoseini, M. H. Aghkhani, and A. Sharifi. 2014. The behavior of tillage tools with acute and obtuse lift angles. Spanish Journal of Agricultural Research (1): 44-51.
2. Armin, A., R. Fotouhi, and W. Szyszkowski. 2017. Experimental and Finite Element Analysis for Mechanics of Soil-Tool Interaction. World Academy of Science, Engineering and Technology, International Journal of Mechanical, Aerospace, Industrial, Mechatronic and Manufacturing Engineering 11 (2): 433-439.
3. Azimi zadeh, Z., S. H. Karparvarfard, and H. Azimi- Nejadian. 2019. Evaluation of a Narrow Blade to Improving the Combined Tillage performence. Iranian Journal of Biosystems Engineering 50 (2): 253-266. (In Farsi).
4. Eshaghbagi, A., A. Tabatabaeifar, A. Kayhani, and M. H. Raoufat. 2004. The effect of depth and angle of attack on the pull resistance of the subsoiler with a bent blade. Journal of Agricultural Science of Iran 36 (4): 1045-1052.
5. Godwin, R. J., and G. Spoor. 1977. Soil failure with narrow tines. Journal of Agricultural Engineering Research 22 (3): 213-228.
6. Ibrahmi, A., H. Bentaher, E. Hamza, A. Maalej, and A. M. Mouazen. 2017. Advanced analytical method of mouldboard plough’s design. The International Journal of Advanced Manufacturing Technology 88 (1-4): 781-788.
7. Ibrahmi, A., H. Bentaher, M. Hbaieb, A. Maalej, and A. M. Mouazen. 2015. Study the effect of tool geometry and operational conditions on mouldboard plough forces and energy requirement: Part 1. Finite element simulation. Computers and Electronics in Agriculture 117: 258-267.
8. Karayel, D., and E. Sarauskis. 2019. Environmental Impact of No-Tillage Farming. Environmental Research, Engineering and Management 75 (1): 7-12.
9. Karparvarfard, S. H., and H. Rahmanian-Koushkaki. 2015. Development of a fuel consumption equation: Test case for a tractor chisel-ploughing in a clay loam soil. Biosystems Engineering 130: 23-33.
10. Mohammadi, M., S. H. Karparvarfard, S. Kamgar, and M. Rahmatian. 2018. Optimization and evaluation of working conditions for a new narrow blade for use in combined tillage. Journal of Agricultural Machinery 10 (2). doi:10.22067/jam.v10i2.73914. (In Farsi).
11. Moitzi, G., R. W. Neugschwandtner, H. P. Kaul, and H. Wagentristl. 2019. Energy efficiency of winter wheat in a long-term tillage experiment under Pannonian climate conditions. European Journal of Agronomy 103: 24-31.
12. Nasseri, A. 2019. Energy use and economic analysis for wheat production by 450-459.
13. Or, D., and T. A. Ghezzehei. 2002. Modeling post-tillage soil structural dynamics: a review. Soil and Tillage Research 64 (1-2): 41-59.
14. Reicosky, D. C., and R. R. Allmaras. 2003. Advances in tillage research in North American cropping systems. Journal of Crop Production 8 (1-2): 75-125.
15. Renton, M., and K. C. Flower. 2015. Occasional mouldboard ploughing slows evolution of resistance and reduces long-term weed populations in no-till systems. Agricultural Systems 139: 66-75.
16. Rowe, R. J., and K. K. Barnes. 1961. Influence of speed on elements of draft of a tillage tool.‏ Transactions of the ASAE, 4: 55-57.
17. Tabatabaeefar, A., H. Emamzadeh, M. Ghasemi Varnamkhasti, R. Rahimizadeh, and M. Karimi. 2009. Comparison of energy of tillage systems in wheat production. Energy 34 (1): 41-45.
CAPTCHA Image