Modeling
M. Mehrijani; J. Khodaei; S. Zareei
Abstract
Introduction Tillage as a preliminary step for agricultural production consumes large amounts of energy. Regarding the energy crisis and the greenhouse gas emissions caused by the indiscriminate use of fossil fuels, many efforts have been done to reduce energy consumption as much as possible. About half ...
Read More
Introduction Tillage as a preliminary step for agricultural production consumes large amounts of energy. Regarding the energy crisis and the greenhouse gas emissions caused by the indiscriminate use of fossil fuels, many efforts have been done to reduce energy consumption as much as possible. About half of the energy used in the crop production has been dedicated to tillage operations; hence the optimization of tillage tools performance can lead to decrease the energy loss. Tillage operation in most regions of Iran is carried out by moldboard plow. The ability of this plow in turning the soil has made it impressively different from the other plows. The energy used in tillage operations depends on various factors such as soil type and its conditions (soil moisture and texture), plow depth and forward speed. The aim of this study is to investigate the effect of forward speed, plow depth and soil moisture on fuel consumption and required tensile force during tillage operation with a moldboard plow which uses three plows in clay soil. Materials and Methods The current study was carried out to optimize the tillage operation with a moldboard plow in the clay soil. Tillage experiments were performed to evaluate the effect of forward speed, plow depth and soil moisture content on the required tensile force and tractor fuel consumption. A moldboard plow with three single-sided plows was used to conduct experiments. Two tractors (MF285 and U650) and a dynamometer were used to measure the required tensile force. To measure the fuel consumption of the tractor during operation, the fuel level was measured in a separate tank system installed on the tractor's fuel system. Experiments were carried out using response surface method and central composite design (CCD) by taking three levels of forward speed (4, 5 and 6 kmh-1), three plow depth (20, 25 and 30 cm) and three levels of soil moisture content (12, 16 and 20%). Design Expert 8.0.6 software was used to analyze the experimental data. Results and Discussion The result of the analysis of variance showed that the effects of plow depth, forward speed and soil moisture, as well as the interaction between forward speed and moisture content on the fuel consumption during tillage operations with moldboard plow are significant. The results also indicated that the increase in forward speed decreased the fuel consumption. Also, fuel consumption decreased with increasing in moisture content at first, but then increased. The reason for this was probably because of the increased strength of soil particles due to the reduced moisture content (the stronger coherence force between the particles), which required more energy to shear the soil. According to the results of analysis of variance, it can be concluded that all three factors of forward speed, plow depth and soil moisture had a significant effect on the required tensile force of moldboard plow at %1 probability level. With increasing the plow depth and forward speed, required tensile force increased significantly. The dependent variables were modeled as second order regression equations and optimal values of independent variables were determined. Optimum performance with maximum desirability was determined at forward speed of 5.08 kmh-1, plow depth of 20 cm and soil moisture content of 16.41%. Conclusion With increasing plow depth, tensile force and fuel consumption increased. Also, tensile force increased with increasing forward speed, but this increase was not severely affected by the plow depth and reduced the fuel consumption. The quadratic regression models can well predict the required tensile force and fuel consumption. Using response surface method, optimum performance was determined at forward speed of 5.08 kmh-1, plow depth of 20 cm and soil moisture content of 16.41%.
M. Naghipour Zade Mahani; K. Jafari Naeimi; M. Shamsi; Gh. Mohamadi Nejad
Abstract
Due to the importance of weed control and the limitations of mechanical methods in some places, in this research the water jet cutting for weed control was investigated. The cutting tests were performed on camel thorn weed in Shahid Bahonar university of Kerman. The water jet pressure of 90 bars was ...
Read More
Due to the importance of weed control and the limitations of mechanical methods in some places, in this research the water jet cutting for weed control was investigated. The cutting tests were performed on camel thorn weed in Shahid Bahonar university of Kerman. The water jet pressure of 90 bars was achieved with the aid of a suitable pump. The cutting time was studied in a completely randomized factorial design experiment (CRD) with five replications. Factors of experiments are: stem diameter in 2 levels (smaller and larger than 5 mm), distance of spraying jet from weeds in 3 levels (10, 20 and 30 cm) and two types of plant holders: blade and plate. The results showed that stem diameter and jet distance from the weed stem had significant effects on cutting time (at the 1%). The mean comparison of parameters showed that with increase of stem diameter the cutting time increased and any increase in jet distance from the weeds decreased the cutting time linearly with R2=0.96 and R2=0.99 for small and large diameter weeds, respectively. The minimum cutting time was measured at 30 cm of the jet from small diameter of stems. A multivariate linear regression model was also proposed for cutting weed parameters. It can be concluded that due to the flexibility of water jet cutting for restricted places, hydrodynamic control of weeds is proposed as a complementary method and sometimes a competing substitute method.
Design and Construction
J. Baradaran Motie; M. H. Aghkhani; M. H. Abbaspour-Fard; A. Lakziyan
Abstract
The issue of soil salinity is one of the snags for increasing agricultural productivity, which must be inhibited by appropriate devise and scientific management. One way to identify salty areas of farm lands is to prepare salinity maps. In this study, a prototype soil apparent electrical conductivity ...
Read More
The issue of soil salinity is one of the snags for increasing agricultural productivity, which must be inhibited by appropriate devise and scientific management. One way to identify salty areas of farm lands is to prepare salinity maps. In this study, a prototype soil apparent electrical conductivity measuring and mapping device, was designed and built. This device employs direct contact method of electrodes with soil (Also called Wenner method). The system inputs include power supply voltage, location signal from a GPS receiver and signal of voltage between the electrodes. The outputs include the apparent electrical conductivity with respective to geographical coordinate that created in a TEXT file, and then transmitted through a RS-232 serial port to a PC. Electrical conductivity data calibrated and mapped using ESAP-95 software package. To evaluate the device, electrical conductivity map of a land with area of 0.8 Ha surveyed in two ways: using the on the go EC mapper and capturing soil samples manually. The results of these two methods were then compared. Assessment of the device in a clay-loamy soil with low salt level, showed a good correlation with the laboratory EC, having mean error (ME) of -15.27μS.cm-1. Point to point comparison between surveyed data and laboratory EC’s shown that in 67 percent of measurements the errors were under 10 percent. These errors are acceptable mainly due to unknown soil variables and in comparison with other research findings.
